Pioneer S-LX70W - Manual (Page 6)

6
En
• The installation location selected should have a sturdy
floor surface. Mounting the speaker on a long-pile
carpet should be avoided, since the carpet may touch
the driver’s diaphram, causing distorted sound.
• Please install this unit away from the antenna cable of
the tuner, as noise can be caused with installation
close to the antenna cable. In such a case, use this
unit at a position away from the antenna and the
antenna cable, or when playback of extra bass is not
required, switch off the power for this unit.
PANEL FACILITIES
FRONT PANEL
REAR PANEL
1 Power Indicator (STANDBY/ON)
Lights blue when the power has been switched ON.
When AUTO STANDBY switch is set to ON, lights blue
whenever the speaker receive an audio signal. If the
power is switched OFF only briefly, the indicator lights
blue when power is restored. If no signal is present for
more than 12 minutes, the subwoofer automatically
reverts to standby mode and the power indicator lights
red. If, subsequently, a signal is received, power
automatically comes back on and the power indicator
lights blue.
NOTE:
• If you are planning on switching the unit OFF for a long
period of time, make sure to check that the indicator
light has gone out after switching OFF.
2 Power switch (POWER)
When pressed, power is turned ON; when pressed
again, power is turned OFF.
3 Volume knob (VOLUME)
Sets the subwoofer volume.
• Turn the knob slowly from the MIN position.
• With this unit, the bass level can be independently
set, so do not turn up the bass on the AV amplifier.
4 Crossover knob (CROSSOVER)
When using the subwoofer, set the upper frequency
limit for the subwoofer (
50 Hz, 60 Hz, 70 Hz, 80 Hz,
100 Hz, 120 Hz, 160 Hz, 200 Hz ) so that it
complemets the output from your other speakers.
When using the bass managment features of an AV
receiver, set to
BYPASS ON in order to use the low-
pass filter of the AV receiver for high quality sound.
5 Bypass switch (BYPASS)
When set to ON , the audio signal is routed directly to
the woofer unit, bypassing the amplifier’s filter.
6 Bass mode switch (BASS MODE)
MUSIC : The characteristic frequencies become flat.
Recommended for music sources.
CINEMA : Low frequencies are emphasized.
Recommended for sources that require strong bass.
7 Phase switch (PHASE 0º /180º)
When set to 180º , the output phase becomes the
reverse of the input signal, and when set to 0º , it is in
the same phase as the input signal.
• Normally, the switch is set to
0º .
But when the sound connection between the
subwoofer and the left and right speakers sounds
unnatural, try switching to
180º and set the switch
in the position where the sound is natural.
• When using two or more subwoofers together,
make sure that the phase switch of all of them are
set to the same position.
MAINTENANCE OF EXTERNAL SURFACES
• Clean the surface by wiping with the provided
polishing cloth, or with another soft, dry cloth.
• When the surfaces are very dirty, wipe with a soft
cloth dipped in some neutral cleanser diluted five
or six times with water, and wrung out well, and
then wipe again with a dry cloth. Do not use
furniture wax or cleaners.
• Never use thinners, benzine, insecticide sprays
and other chemicals on or near this unit, since
these will corrode the surfaces.
POWER
STANDBY/ON
2
1
VOLUME
CROSSOVER
MAX MIN
200Hz
160Hz
120Hz 100Hz 80Hz 70Hz
60Hz
50Hz
BYPASS
ON OFF
BASS MODE MUSIC CINEMA
PHASE 180 ∞ 0 ∞
AUTO STANDBY OFF ON
LINE LEVEL
OUTPUT INPUT
AC IN
4
5
9 11
3
6
7
8
10
S_LX70W_En.book 6 ページ ２００７年７月１０日 火曜日 午後３時９分