Panasonic BT-H1700AE - Manual (Page 17)

ENGLISH
15
<FUNCTION SETTING>
COLOR SYSTEM :AUTO
SYNC SELECT :INT.
RUSH DELAY TIME :STD.
TALLY SELECT :GREEN
REMOTE SYSTEM :MAKE
EMBEDDED :1G
HOUR METER X100h :000
EXIT: MENU ADJUST:- + SELECT:
Ⅵ ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS
1. FUNCTION SETTING
Selects the colour system and
displays the monitor’s power-
up time or the total usage time.
Press the
button to display
the setting menu illustrated on
the right.
Item : COLOR SYSTEM
Settings : AUTO/NTSC/PAL
Function : Selects the colour system when using the video
input card.
AUTO : Change NTSC and PAL automatically.
NTSC : Keeps the colour system NTSC.
PAL
: Keeps the colour system PAL.
NOTE : Normally select AUTO. However, if the input signal is
unstable, select NTSC or PAL.
Item : SYNC SELECT
Settings : INT./EXT.
Function : Synchronised signal selection.
INT. : The input video signal is synchronised
with the built-in sync signal.
EXT. : The input video signal is synchronised
with an external signal from an external
sync terminal.
* The external synchronised signal terminals apply to the HD/
CS terminal and VD terminal (in the RGB/COMPONENT Input
Card), or the EXT. SYNC terminal (in the VIDEO Input Card).
* This item is not shown when only SDI and/or HD SDI input
cards are installed.
Item : RUSH DELAY TIME
Settings : STD./SLOW
Function : Sets the time when the power supply to the
monitor’s circuits (excluding the micro computers)
starts after the power switch is pressed.
STD.
: The power supply starts approx.
1 second after the power switch is
pressed.
SLOW : The power supply starts approx.
3.2 seconds after the power switch is
pressed.
NOTE : If you are going to turn several Multi-Format Monitors
on at the same time, it is recommended to apply
SLOW to some of the monitors to control rush current.
Item : TALLY SELECT
Settings : GREEN/RED
Function : Selects the colour of the tally lamp (when lit) on
the upper front panel.
GREEN: The tally lamp lights in green.
RED
: The tally lamp lights in red.
NOTE : Set the MAKE/TRIGGER terminal’s tally control in the
REMOTE (external control) terminal setup menu. For
details, refer to Page 19. To set the color, use TALLY
SELECT in the “FUNCTION SETTING” setup menu or
MAKE/TRIGGER in the REMOTE (external control)
terminal setup menu. For details, refer to Page 15 and 19.
Item : REMOTE SYSTEM
Settings : MAKE/TRIGGER
Function : Selects the contact system (MAKE (make
contact) or TRG. (trigger contact)) for the MAKE/
TRIGGER terminals.
MAKE (make contact system): Controls the
function by stable disconnection (terminal
open) or short-circuit (short with GND of 15th
terminal) of the controlled terminal.
TRG. (trigger system): Controls the function by
instantaneously (one second) short-circuiting
(short with GND of 15th terminal) the controlled
terminal.
Item : EMBEDDED
Settings : 1G/2G/1-2G
1G :
2G :
1-2G :
Function : Selects Embedded Audio signal channels.
NOTE : The auto setting mixes and outputs all 8 signal channels.
Output level is automatically detected and set at FPGA
according to the channel numbers that are receiving signals.
* About sound output level
Sound output level is set to a standard output level for all
channels when several sound channels are output at the
same time. The more channels are selected, the lower each
channel’s level will be.
(Each channel's level becomes half for 1– 2 channel, 1/4 for
1– 4 channel.)
*About AUTO
When AUTO is selected, the number of sound channels in use
is detected. The level of each channel is automatically
adjusted to ensure that the total sound output level is equiva-
lent to the standard output level.
* This item is shown when an input card compliant with EM-
BEDDED AUDIO is installed.
Item : HOUR METER X100h
Number
range
: 000 ~ 655
Function : Displays the total usage time of the monitor in
hundred-hour units.
<PICTURE SUB ADJ.>
CONTRAST : 00
BRIGHT : 00
CHROMA : 00
PHASE : 00
NTSC SETUP : 00
COMPO.LEVEL :SMPTE
sub menu
reset
EXIT: MENU ADJUST:- + SELECT:
● When the timer passes 655, it returns to 000.
● The timer does not count the usage time under one hour.
2. PICTURE SUB ADJ.
Performs approximate
adjustments using the control
knobs on the front panel. Press
the
button to display the
setting menu illustrated on the
right.
NOTE : When the RGB signal
is input, only
CONTRAST and
BRIGHT are displayed. When the PAL signal is
input, only CONTRAST, BRIGHT and CHROMA are
displayed.
1ch 2ch 3ch 4ch 1-2ch 3-4ch 1-4ch
5ch 6ch 7ch 8ch 5-6ch 7-8ch 5-8ch
AUTO 5-8ch 1-4ch 7-8ch 5-6ch 3-4ch
1ch 2ch 3ch 4ch 5ch 6ch 7ch 8ch 1-2ch
LCT1261-001A (EN) 02.6.25, 12:25 PM 17