Peavey PM 1 - Manual (Page 4)

DESCRIPTIONS
POWER
The PM One is supplied with a switchable power supply. Before plugging your PM One in, please
read this entire section to ensure proper supply voltage selection and unit operation. It is important
that all safety precautions be followed.
1. VOLTAGE SELECTOR SWITCH
Use this switch to select the proper AC supply voltage for your area. This voltage varies from one
geographical area to another. For voltages between 110 and 120 VAC, select the 115 position.
For voltages between 220 and 230 VAC, select the 230 position.
2. IEC POWER CORD
This receptacle is for the IEC line cord (included), which provides AC power to the unit. Connect
the line cord to this connector and to a properly grounded AC supply. Damage to the equipment
may occur if an improper line voltage is used. (See voltage marking on unit.) Never remove or
cut the ground pin of the line cord plug. This unit is supplied with a properly rated line cord.
When lost or damaged, replace this cord with one of the proper ratings.
NOTE: FOR UK ONLY
As the colors of the wires in the mains lead of this apparatus may not correspond with the colored
markings identifying the terminals in your plug, proceed as follows: (1) The wire which is colored
green and yellow must be connected to the terminal which is marked by the letter E or by the earth
symbol or colored green or green and yellow. (2) The wire which is colored blue must be
connected to the terminal which is marked with the letter N or the color black. (3) The wire which
is colored brown must be connected to the terminal which is marked with the letter L or color red.
3. POWER ON/OFF SWITCH and LED
The Power On/Off Switch is located on the front of the PM One. (Top panel. See diagram on
page 6.) This switch in the (l) position will turn the unit on if proper voltage is supplied. The power
LED located next to the switch will illuminate when the unit is on. WARNING: PROPER
VOLTAGE MUST BE SELECTED BY THE VOLTAGE SELECTOR SWITCH (1) BEFORE THIS
SWITCH IS TURNED ON. FAILURE TO SELECT THE PROPER VOLTAGE APPLICABLE TO
YOUR POWER SOURCE COULD RESULT IN DAMAGE TO YOUR PM ONE MIXER.
4. FUSE (0.5A/250V)
The fuse is located within the cap of the fuseholder (on back panel). If the fuse should fail, IT
MUST BE REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE
TO THE EQUIPMENT AND TO PREVENT VOIDING THE WARRANTY. If the unit repeatedly
blows fuses, it should be taken to a qualified service center for repairs.
WARNING: THE FUSE SHOULD ONLY BE REPLACED WHEN THE POWER CORD HAS
BEEN DISCONNECTED FROM ITS POWER SOURCE.
REAR PANEL
4
CHANNEL
FOUR
CHANNEL
THREE
CHANNEL
TWO
CHANNEL
ONE
OUTPUT
GND MIC 2
WARNING: TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK DO NOT EXPOSE
RISQUE DE CHOC ELECTRIQUE -
THIS EQUIPMENT TO RAIN OR MOISTURE.
TO PREVENT THE RISK OF FIRE HAZARD,
AVIS:
NE PAS OUVRIR. REMPLACER PAR UNFUSI-
REPLACE WITH SAME TYPE 250 VOLT FUSE.
BLE DE MEME TYPE ET DE 250 VOLTS.
115 U S E F FU S E
FU S E E S U F R
L
R
L
R
L
R
L
R
L
R
L
LINE 5 AMP REC LINE 4 LINE 3 LINE 2 PHONO 2 LINE 1 PHONO 1
F 500 mA
250V
120V 60Hz/230V 50Hz
20 WATTS
A PRODUCT OF PEAVEY ELECTRONICS CORP.
MERIDIAN MS.
TM
P R O D U C T I O N
M I X E R
ONE
230V
115V
1 4 2 5 6 7 8 10