Peavey CA6-X User Manual

Page 2

Advertising
background image

v. 1.0 08/13/97

C A 6 - X P OW E R A M P L I F I E R

P R E L E I M I N A RY S P E C I F I C AT I O N S

Crest Audio Inc.

100 Eisenhower Dr., Paramus NJ 07652 USA

TEL

: 201.909.8700

FAX

: 201.909.8744

http://www.crestaudio.com

Power figures are watts per chan-
nel, both channels driven.

* 3-Year Warranty with 2 addi-
tional years if Registration Card
is sent to Crest Audio. (USA,
Canada, United Kingdom, and
many other countries).

Crest Audio reserves the right to
make improvements in manufac-
turing or design which may affect
specification.

Crest Audio specification litera-
ture is available in downloadable
PDF format; visit our website at:
http://www.crestaudio.com.

©1997 Crest Audio Inc.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS : RISQUE DE CHOC ÉLECTRIQUE—NE PAS OUVRIR

WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT

EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

ATTENTION! POUR ÉVITER LE RISQUE D'INCENDIE OU DE CHOC

ÉLECTRIQUE, NE PLACEZ PAS CET APPAREIL SOUS LA PLUIE OU Á

L'HUMIDITÉ

CAUTION

A

A B

A B

A

Designed & manufactured in the USA by:

Crest Audio Inc.

100 Eisenhower Dr.

Paramus, New Jersey 07652 USA

1

3-

2+

+

A

A

B

B

• •

• •

+
+

+

A

B

B

A

A

B

Designed & manufactured in the USA by:

Crest Audio Inc.

100 Eisenhower Dr.

Paramus, New Jersey 07652 USA

A

A B

A B

A

1

3-

2+

+

• •

• •

B

A

NL4FC

B

A

A

B

643-105

A

A

B

B

Rear View,

Binding Post

Version

Rear View,

Speakon

Version

(not available in

North America)

1kHz, 0.01% THD+N

20Hz-20kHz, 0.1% THD+N

400W

350W

600W

500W

1200W

1000W

73V

103V

20Hz-20kHz, -3dB@135kHz

20Hz-20kHz, -1.1dB/+0dB

ACL, IGM, AutoRamp, short circuit, DC voltage,

turn-on/off transient, current inrush, sub/ultrasonic input.

<0.01%

<0.01%

400:1

> - 60dB

1.40V standard (see table below)

X37.7 standard (see table below)

>20k

/>10k

-105dB

> - 60 dB

H

Female XLR (pin 2+, dealer configurable for pin 3+), TRS (tip+)

5-way output binding posts or Speakon connectors

(market dependent)

68,000

µ

F

100V-240V, 50-60Hz

1.6A

6A

13.0A

21A

2630 BTU/hr

3713 BTU/hr

Back-to-front via 2 rear panel mounted variable-speed DC fans

(filters removable without tools)

Front Panel: 2 attenuators, located behind blanking plugs

Rear Panel: signal ground lift switch, mode select switch

Clip/Limit, Signal, Temp/DC, Active

Steel chassis, 16 gauge. Double thickness in rack ear areas.

3.5" x 19" x 18" / 89 x 483 x 457mm

49 lbs. / 22.25 kg., 44 lbs. / 19.98 kg.

5 years

*

8

Stereo Power

4

Stereo Power

8

Bridged Mono Power

Max RMS Output Voltage

(each channel)

Peak Output Voltage

(each channel)

Frequency Response

(+0 / -0.3dB, 1W/8

)

Power Bandwidth

(rated power at 4

, 1% THD+N)

TourClass

®

Protection

THD+N

(rated power at 4

, 1kHz)

SMPTE IMD

(rated power at 8

, 60Hz & 7kHz)

Damping Factor

(10-400Hz at 8

)

Input CMRR

(1kHz)

Input Sensitivity

(rated power at 8

)

Voltage Gain

Input Impedance (balanced/unbalanced)

Hum and Noise

(“A” weighted, full power, 4

)

Crosstalk

(“A” weighted, full power, 4

)

Class

Input Connectors

(per channel)

Output Connectors

(per channel)

Filter Storage

Power Supply

(factory configured)

Idle Current Draw 120V

1/8 Power Curr. Draw

(typical music, 120V/4

)

1/3 Power Curr. Draw

(continuous music, 120V/4

)

Max Curr. Draw

(circuit breaker rating, 120V/4

)

Thermal Emissions

(1/8 Power, 4

)

Thermal Emissions

(1/3 Power, 4

)

Cooling

Controls

LED Indicators

(per channel)

Construction

Dimensions

(Height x Width x Depth)

Gross Weight, Net Weight

Warranty

Gain

Sens

Dealer-Configurable Gain/Sensitivity Options

Factory Standard

X37.7

1.40V

Option 1

X40.0

1.32V

Option 2

X20.0

2.65V

*B5000017*

Architect’s & Engineer’s Specifications

The power amplifier shall have two channels. At 8 ohms, 20Hz
- 20kHz, 0.1% THD+N, it shall deliver a minimum of 350 watts
per channel. At 4 ohms, 20Hz - 20kHz, 0.1% THD+N, it shall
deliver a minimum of 500 watts per channel. In bridged mono
mode with an 8 ohm load, 20Hz - 20kHz, 0.1% THD+N, it
shall deliver a minimum of 1000 watts.
The amplifier shall have circuitry to protect itself from output
short circuits, thermal overload or other adverse load condi-
tions. The amplifier shall protect speaker loads from DC volt-
age on outputs. The amplifier shall have active clip limiting
and impedance sensing circuitry. Output relays shall protect
the speakers from amplifier failure.
Two rear panel mounted variable speed DC fans (filters
detachable without tools) shall provide back to front air flow
through the chassis.
Each channel shall have a standard (factory-set) input sensitiv-
ity of 1.40 Volts, and shall be fitted with an internal jumper
which allows the gain to be altered to X20 or X40. The hum
and noise level shall be 105 dB below rated output, “A”
weighted. SMPTE IMD shall be less than 0.01% at rated
power, 60Hz and 7kHz. The amplifier shall have a class H out-
put stage. The frequency response shall be 20Hz-20kHz, +0,
-0.3dB (1W/8

).

The amplifier will operate at 100V-240V, 50-60 Hz AC (config-
ured at factory). Maximum current draw shall not exceed 21
amperes at 120VAC (limited by front panel breaker for bench
tests).
Front panel indicators shall include Active, Protect, Signal,
and Clip LED’s for each channel. Front panel attenuators
shall be detented and located behind blanking plugs.
Rear panel input connectors shall be female TRS and XLR
type, internally dealer-configurable for pin 2 (factory setting)
or pin 3 positive. Output terminations shall be 5-way output
binding posts or Speakon output connectors (market depen-
dent). A ground lift switch and a Stereo/Parallel/Bridged Mono
mode operation switch shall be provided.
A rear-panel IEC AC mains socket (with power cord) or single
AC mains cord having an appropriate AC plug for the intended
operating voltage shall be provided (market dependent).
The packaging of the amplifier shall allow for standard rack
mounting without requiring space between similar units.
Optional rack mount handles will be available. Dimensions
shall be 19" (483mm) wide, 3.5" (8.9mm) high and 18"
(457mm) deep. The amplifier shall weigh 44.0 lbs. (19.98 kg.)
net, and shall be designated the Crest Audio model CA6-X.

Advertising