Polk Audio RMDS-1 - Manual (Page 16)

Polk customer service (800) 377-7655 16
COAX1 DIGITAL
STEREO TEST MEMO AUTO
PCM
power ———— standby
source
on/off
surround multi-room tune
save
preset clear presets
TUNED
OPT NIGHT PROLOGIC
P-SCAN STEREO
MULTI COAX2
db
kHz
MHz
DOLBY
D I G I T A L
R M D I G I T A L S O L U T I O N I N T E L L I G E N T A / V P R E A M P / P R O C E S S O R / L O U D S P E A K E R S Y S T E M
aux. inputs S-video
volume
video L..audio..R
COAX1 DIGITAL
STEREO TEST MEMO AUTO
PCM
power ———— standby
source
on/off
surround multi-room tune
save
preset clear presets
TUNED
OPT NIGHT PROLOGIC
P-SCAN STEREO
MULTI COAX2
db
kHz
MHz
DOLBY
D I G I T A L
R M D I G I T A L S O L U T I O N I N T E L L I G E N T A / V P R E A M P / P R O C E S S O R / L O U D S P E A K E R S Y S T E M
aux. inputs S-video
volume
video L..audio..R
Memory
indicator
Tuned
indicator
FM Stereo
indicator
FM auto
indicator
Power switch
Remote
sensor
window
Source
selector
Surround
selector
Radio signal
strength meter
Test tone
indicator
Multi
room
selector
Manual
radio
tuning
Radio
presets
selector
Auxillary
audio/video inputs
(under cover)
Save
preset
Clear
Standby Main display Volume
Late night
mode indicator
Preset scan
indicators
Multi room
indicator
Surround mode
indicator
lights
Digital
input
indicator
Power Switch And Standby Indicator
When this switch is pressed once, the power turns ON and lights appear
on the Main Display panel. When pressed again, the power turns OFF
and the standby indicator light glows red. Make sure the Power switch
on the back of the subwoofer enclosure is set to the “On” position.
When you turn on the preamp/processor, the amplifiers in the
subwoofer enclosure will also turn on and you will see a green glow on
the base of the subwoofer. When the preamp/processor is turned “Off”
the amplifiers turn off, and the light in the subwoofer base glows red.
Main Display
Displays a variety of information depending on what action was most
recently taken. Normally, it indicates the current selected input (CD,
DVD, etc.). It also displays the current selected surround mode (Stereo,
Pro Logic, or Dolby Digital) as well as volume, bass level, and other
information on a “flash” basis. See the next page for an explanation of
all those little teeny lights.
Volume Control
Adjusts the overall sound level. Turning the control clockwise increases
the sound level, turning it counter-clockwise decreases the volume level.
Remote Sensor Window
This window receives infrared signals from the remote control unit. Aim
the remote control unit to this sensor window. Do not allow any solid
object to block the path between the remote control and this window.
Source Selector Buttons
These buttons are used to select the source of sound and video such as
DVD, DSS, VCR, LD, and AUX. Video and audio are switched
simultaneously on those inputs that have both video and audio input
jacks. For example, when you select DVD, the picture and sound of the
DVD player are automatically switched on together. The buttons toggle
through the inputs in the following sequence:
See page 22 for more information on using this feature.
IMPORTANT NOTE:
The FM radio, AM radio, CD, and Tape audio inputs do not have
corresponding video inputs. When you select any of these sources,
you will see a blank screen on your TV (if your TV is on).
PREAMP/PROCESSOR FRONT PANEL
GUIDED TOUR