PYLE Audio PYD-710 - Manual (Page 3)

Pyle Pro Mixer Owner’s Manual – 3 2 – Pyle Pro Mixer Owner’s Manual
Presetting the Controls Before Use
Since sudden high output levels from your Pyle Pro mixer can damage not only audio devices connected
to the mixer output but your hearing as well (especially if you are using headphones), please adjust
the mixer’s controls BEFORE connecting AC power or turning on the unit.
Set up the mixer controls like this before you start:
Playing the Mixer’s Output Signal
To record the mixer’s output signal, connect audio patch cords (not supplied) from the mixer’s REC
(Record) L and R jacks to your tape deck’s left and right input jacks.
Power On/Off
Balance
Gain
Tone Controls, Treble, Mid and Bass
MIC 1/2, CH 1/2/3, Master and Cue Levels
Crossfader
OFF
MID
MID
0
0
CENTER
CONTROL SETTING
Connecting the Outputs
After presetting the controls (above), you can then connect the mixer’s output jacks to the output
devices’ input jacks. Before connecting these devices, however, be sure to preset their controls to
avoid any damage to your equipment due to unexpected high output levels.
Set the output devices’ controls like this before you start:
Tape Deck
Amplifier/Receiver OFF
OFF
FLAT
OUTPUT DEVICE SETTING CONTROL
POWER
POWER
TONE
To play the mixer’s output signal through your speaker system (for events such as parties, dances,
conferences, etc.) connect an audio patch cord with RCA-type jacks (not supplied) from the mixer’s
MASTER L and R jacks to your receiver/amplifier’s left and right input jacks.
Recording the Mixer’s Output Signal
3. Turntables. Connect up to 2
turntables to the Phono 1 and Phono
2 input jacks. Please note that Phone
1 and Line 1 (as well as Phono 2 and
Line 3) use the same jacks. The
selector switch below the jacks should
be set to Phono position if the jacks
are used for phono inputs.
When using a turntable, you should
also securely connect its ground wire
(usually green or black) to the Ground
screw on the input panel of the mixer.
This mixer permits connection of up to five (5) audio input sources, including a microphone. Such a
system might include, for example:
One Microphone
Two Turntables
Two CD players
Please observe
the following:
Do not connect any audio source with a HIGH LEVEL OUTPUT to the LOW
LEVEL PHONO 1 or PHONO 2 mixer audio input jacks (an audio source
output with a volume control is HIGH LEVEL).
Connect audio inputs as follows:
1. DJ Microphone. Connect
the DJ’s Microphone (not
supplied) to the mic input jack.
The special combo jack on the
PYD-720 permits you to connect
with either a 1/4” plug or XLR
plug.
Connecting the Mixer Inputs
One Microphone
One Turntable
Two CD players
One Cassette Deck
One Microphones
One Turntables
One CD player
One Cassette Decks
One VCR
One Microphone
Two Turntables
One CD player
One Rhythm Synth
High Level Output
Audio Source
Use RCA type
patch cables
LEFT output
RIGHT output
Be sure to place the input select switch(es)
in positions which reflect what the connected
input source is (Line in or Phono In)!
CD player, cassette deck, camcorder, VCR, etc.
NOTE!
2. High Level Output Audio
Sources. Connect up to 4
such sources (tuner, cassette
deck, CD Player, camcorder
or VCR) to the input jacks for
Line 1 (if not being used as
Phono 1 input), Line 2, Line
3 (if not being used as Phono
2 input), and Line 4. Please
note that Phono 1 and Line 1
(as well as Phono 2 and Line
3) use the same jacks. The
selector switch(e)s below the
jacks should be set to Line
position if the jacks are used
for the High Level input
sources described here.
Use RCA type
patch cables
LEFT output
RIGHT output
Magnetic cartridge turntable
GROUND wire from turntable
Use 1/4”
jack
PYD-710
DJ MIC
DJ MIC
Use 1/4” or
XLR-type jack
PYD-720