Panasonic PT-AE200U - Manual (Page 30)

58-E NGLISH E NGLISH -59
Other
s
Specifications
Power supply: 100 V–240 V ~, 50 Hz/60 Hz
Power consumption: 180 W (During standby (when fan is
stopped): Approx. 1.5 W)
Amps: 2.2 A–1.0 A
LCD panel:
Panel size (diagonal): 0.7 type (17.78 mm)
Aspect ratio: 16:9
Display method: 3 transparent LCD panels (RGB)
Drive method: Active matrix method
Pixels:
PT-AE300U: 518 400 (960 x 540) x 3 panels
PT-AE200U: 415 272 (858 x 484) x 3 panels
Lens: Manual zoom (1 - 1.2) / focus lens
F 2.0 - 2.3, f 22.0 mm - 26.2 mm
Lamp: UHM lamp (120 W)
Luminosity:
PT-AE300U: 800 lm (ANSI)
PT-AE200U: 700 lm (ANSI)
Scanning frequency: (for RGB signals):
Horizontal scanning frequency: 30 kHz–70 kHz
Vertical scanning frequency: 50 Hz–87 Hz
Dot clock frequency:
Less than 100 MHz
YP B P R signals: 525i (480i), 625i, 525p (480p), 750p
(720p), 1125i (1080i)
Color system: 7 (NTSC/NTSC 4.43/PAL/PAL-M/PAL-
N/PAL60/SECAM)
Projection size: 1016 mm - 5080 mm (40˝ - 200˝)
Throw distance: 1.2 m - 7.4 m (3´11˝ - 24´3˝)
Optical axis shift: 17:1 (fixed)
Screen aspect ratio: 16:9
Installation: Front/Rear/Ceiling/Desk (Menu selection
method)
Speaker: 4 cm x 3 cm oval x 1
Max. useable volume output: 2 W (mono)
Connectors
VIDEO IN:
S2 VIDEO: Single-line, Mini DIN 4-pin
Y 1.0 V [p-p], C 0.286 V [p-p], 75
Ω
VIDEO: Single-line, RCA pin jack
1.0 V [p-p], 75
Ω
PC IN:
RGB: Single-line D-SUB HD 15-pin (female)
R.G.B.: 0.7 V [p-p], 75 Ω
G.SYNC: 1.0 V [p-p], 75 Ω
HD/SYNC: TTL high impedance, automatic
plus/minus polarity compatible
VD: TTL high impedance, automatic
Remote control unit
does not operate.
The picture does not
display correctly.
Picture from
computer does not
appear
Problem Possible cause
B The battery may be weak.
B The battery may not be inserted correctly. (Refer to
page 17.)
B The remote control signal receptor on the projector
may be obstructed. (Refer to page 17.)
B The remote control unit may be out of the
operation range. (Refer to page 17.)
B The correct input signal may not be selected.
(Refer to page 22.)
B The signal format (TV system) may not be set
correctly. (Refer to page 35.)
B There may be a problem with the video tape or
other signal source.
B A signal which is not compatible with the projector
may be being input. (Refer to page 61.)
B The cable may be too long.
B The external video output for the laptop computer
may not be set correctly.
(You may be able to change the external output
settings by pressing the [Fn]+[F3] or [Fn]+[F10]
keys simultaneously. The actual method varies
depending on the type of computer, so refer to the
documentation provided with your computer for
further details.)