PAC J1850 - Manual (Page 3)

Pacific Accessory Corporation - Santa Ana, CA 92705
[email protected] • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
07-07-09
J1850 Class 2 VPW
Class 2 J1850
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0 1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
Arbitration EOD CRC
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0 1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
Class 2 Class 2 J1850
Volume Control/Level Matching:
This feature is very important for matching the volume level of the Motorola kit to
the radio. When you first install the Motorola kit with the BLU-GM29 the volume
may be very loud and distorted. The volume controls on the steering wheel have two
functions while in the “BT Control On” mode. Press and hold the OnStar/Mute button until
a beep is heard to toggle between the two functions.
Function 1 (Radio Volume):The default setting for the volume controls on the steering
wheel will adjust the volume of the radio.
Function 2 (Motorola Volume): The volume controls on the steering wheel will adjust the
volume of the Motorola kit.
By switching between radio volume and Motorola kit volume, you can now adjust the
volumes and match them to an acceptable level. Once the volume level of the Motorola
kit is set you should not have to change it again as all other volume control can be done
though the radio or the phone itself.
To Enter Volume Control Mode:
1. Must be in “BT Control On” Mode
2. Press & hold the OnStar/Mute button until a beep is heard. The driver information center will display “BT Volume On”
3. The volume buttons on the steering wheel will now control the Motorola volume
4. Repeat #2 to turn off Bluetooth volume controls
SRCE
Menu
End Call
Answer Call/
Privacy Mode
Press & hold to
enable/disable
Bluetooth controls
OnStar/Mute
Press and hold to
switch between
volume functions:
Function 1 - Phone volume
Function 2 - Radio volume
Phone Controls
Volume Up
Volume Down
14 Pin Molex
(wire insertion side)
1 7
8 14
Pin # Function C olor
1 G round (-) Black
2 M ute Input (-) Yellow /R ed
3 n/a
4 n/a
5 n/a
6 n/a
7 Audio Input (+) W hite/Blue
8 Battery 12v Yellow
9 Acc 12v R ed
10 n/a
11 n/a
12 n/a Black
13 n/a
14 Audio Input (-) Black/W hite
Installing the BLU-GM29 with other Bluetooth kits: If you are installing the BLU-
GM29 with any Bluetooth kit other than the EGO TALK, Parrot CK3000 or Motorola
IHF1000/1700 you will have to cut the 14-pin plug off of the EGO2SPLIT harness and
hardwire the unit to the Bluetooth kit. Please note that the steering wheel controls WILL
NOT function and you MUST use the controller with any Bluetooth kit other than the EGO
TALK, Parrot CK3000 or Motorola IHF1000/1700.
Cut the 14 pin connector off of the EGO2SPLIT harness and wire it directly to the
Bluetooth kit. Once all connections are made and secured, plug the 12-pin connector
on the supplied EGO2SPLIT harness into the 12-pin receptacle on the SPLITGM29
harness. This must be done BEFORE the SPLITGM29 harness is connected to the
vehicle.
When the Bluetooth kit is active the driver information center will display “ BT
Connected”. Once the Bluetooth kit has been de-activated the driver information center
will display “ BT Off”.
Page 3
BLU-GM29
GM LAN 29bit Universal
Bluetooth Integration Interface
To Vehicle To Factory Radio
EGO2SPLIT
Harness
See Below
for wiring
information.
SPLIT
GM29 Har
ness
Connection Diagram
All Other Bluetooth Kits