Panasonic AG-DVX100 P - Manual (Page 46)

Item/
(display mode)
Description of settings
BEEP SOUND
(Camera)
CLOCK SET
(Camera)
(VCR) For setting the internal calendar of the
camera recorder.
HOUR METER
(Camera)
(VCR) For indicating the total rotational time of the
cylinder head (5-digit display in 1-hour
increments).
TIME SHIFT
(Camera)
(VCR) For adding the time which was set using
this item to the time of the internal calendar
(to compensate for time differences) for
display in the viewfinder and on the LCD
monitor. The clock time after the
compensation is also recorded on the tape.
+23h --- +1h, OFF, –1h --- –23h
(In 1-hour increments)
TAPE PROTECT
(Camera) When the camera recorder is left on
standby for about 5 minutes in the shooting
pause mode, it is automatically set to the
tape protection mode. Which tape
protection mode is to be established is
selected using this item.
POWEROFF: The camera recorder’s power is
set to the OFF mode.
STBY: The cylinder head is set to the stop
mode.
USER FILE
(Camera)
(VCR) LOAD: The settings stored last in the user
file are loaded.
SAVE: The user file settings which have
been changed are saved.
INITIAL: The user file settings are restored
to the factory settings.
O When the LOAD or INITIAL operation
has been performed, set the POWER
switch on the camera recorder to OFF
and then to ON again in order to enable
the settings.
46
Setting menus
The underlining indicates the factory setting.
OTHER FUNCTIONS screen
Item/
(display mode)
Description of settings
REMOTE
(Camera)
(VCR) For setting the operations which are
performed using the accessory wireless
remote control unit. (See page 20 for the
remote control unit settings.)
VCR1: The operation performed by the
remote control unit which has been set
to be used for VCR1 are accepted.
VCR2: The operation performed by the
remote control unit which has been set
to be used for VCR2 are accepted.
OFF: Operations performed by the remote
control unit are not accepted.
DV CONTROL
(Camera) For setting the control method when
backup shooting is to be performed by
connecting a component for backup
purposes to the DV connector.
OFF: The component for backup purposes
is not controlled.
EXT: The component for backup purposes
is controlled using the START/STOP
button on the camera recorder. The
images shot by the camera recorder are
recorded by the component for backup
purposes.
However, the camera recorder does not
record the images.
BOTH: The images shot by the camera
recorder are recorded by both camera
recorder and the component for backup
purposes.
CHAIN: When the tape in the camera
recorder approaches the end during
shooting, recording is automatically
commenced by the component for
backup purposes, which has been set to
the recording standby mode.
DV CMD SEL
(Camera) For setting the recording operation to be
performed by the component for backup
purposes when the START/STOP button
on the camera recorder has been pressed.
REC_P:
The mode is switched between recording
and recording pause.
STOP:
The mode is switched between recording
and stop.
<Note>
Select STOP as the item’s setting if the
component for backup purposes is not
equipped with a recording pause function.
REC LAMP
(Camera) For setting the lighting of the tally lamps.
OFF: The tally lamps do not light.
FRONT: The front tally lamp (by the
microphone) lights.
REAR: The rear tally lamp (by the
viewfinder) lights.
BOTH: Both the front and rear tally lamps
light.
For setting the beep tone to ON or OFF.
OFF
ON
When ON is selected as the setting, the
beep tone is sounded at the times given
below.
O When the beep tone is sounded, the
audio signals from the output connectors
are muted, and the beep tone is output
instead.
[Beep tone sounds once]
O When the POWER switch has been set
to ON
O When shooting has commenced
[Beep tone sounds twice]
O When shooting has been temporarily
stopped
[Beep tone sounds 10 times]
O When the cassette tape has not been
inserted
O When the cassette tape is in the
recording pause mode
O When condensation has formed inside
the camera recorder
O When a problem has occurred in the
camera recorder