Panasonic AJ-P2C002SG - Manual (Page 11)

11 General: Features of the Input/Output unit
Ge
ne
ra
l
(Reference values when Panasonic bland SD memory cards
or SDHC memory cards are used for continuous recording.
Actual recording time depends on the kind of scenes and the
number of clips.)
The values for 8 GB and 16 GB SDHC memory cards are
double and four times the values for the 4 GB card.
For the latest information on P2 cards and SD memory cards
not available in the operating instructions, visit the P2
Support Desk at the following Web site.
https://eww.pavc.panasonic.co.jp/pro-av/
Independent HD SDI output provided as a
standard configuration
The HD SDI signals output from the HD SDI A · B
connectors and the MON OUT connector are independent.
Characters and markers can therefore be set independently
(note that the same signal is output from the HD SDI A
connector and the HD SDI B connector).
SDI output includes embedded audio etc.
Features USB 2.0 port (HOST/DEVICE)
By connecting with a PC via USB 2.0, a P2 card inserted in
the unit can be used as a bulk storage device.
Also, since this unit has a USB HOST capability, it is
possible to store P2 card data on an external hard disk
connected using USB 2.0, to view clips stored on the hard
disk and to write clips stored on the hard disk to the P2 card.
DVCPRO output provided as a standard
configuration
Data can be output to an external device through the
IEEE1394 digital interface. Use a 6-pin type connector. The
unit does not support the bus power.
While operating AVC-Intra, it is impossible to output data
with IEEE1394.
Down converter output provided as a standard
configuration
The MON OUT connector outputs down converter (analog
composite) signals.
Also, output signal from the MON OUT connector can be
switched between an HD SDI signal and a VBS signal.
Remote control connector
By connecting the remote control unit (AJ-RC10G), which is
available as an optional accessory, the unit can be controlled
remotely. (Refer to page 117)
Confirmation of return video signals
It is possible to confirm the return video signals (analog
HD Y signals) supplied to the GENLOCK IN connector of the
unit in the viewfinder to confirm programs.
Only video signals from the same record format can be
confirmed. Note also that the 23.98PsF and 24PsF signals
cannot be confirmed. (Refer to page 187)
DC OUT connector
The DC OUT connector of the unit produces 1.5 A of
electrical current.
By connecting an external switch to this connector, it is
possible to control recording start/stop.
Since a tally lamp can be used by connecting the LED to this
connector, it is useful for shooting video when fixing the
camera on a crane. (Refer to page 119)
Viewfinder connection
From the viewfinder connector of the unit, 1080-59.94i,
1080-50i signals are output.
Confirm images in multi formats by connecting the
viewfinder (AJ-HVF21G), which is available as an optional
accessory. (Refer to page 28)
User button
On the side panel of the unit, 5 user buttons (USER MAIN/
USER 1/USER 2/MARKER SELECT/TEXT MEMO) are
available.
Each user button can be assigned the on/off function for any
frequently used feature among the many features of the unit,
such as SLOT SEL and Y GET. (Refer to page 56)
Approximate Proxy Recording Time (optional) on SD memory
cards
(Except for 24P native mode)
Card No.
(Card Capacity)
MPEG4 recording rate
192 kbps 768 kbps 1500 kbps
RP-SDH256
(256 MB) Approx.
2 h 17 min
Approx.
35 min
Approx.
19 min
RP-SDH512
RP-SDK512
(512 MB)
Approx.
4 h 27 min
Approx.
69 min
Approx.
38 min
RP-SDQ01G
RP-SDK01G
(1 GB)
Approx.
8 h 56 min
Approx.
2 h 19 min
Approx.
77 min
RP-SDQ02G
RP-SDK02G
(2 GB)
Approx.
18 h 11 min
Approx.
4 h 44 min
Approx.
2 h 37 min
RP-SDV024G
(SDHC 4 GB) Approx.
35 h 42 min
Approx.
9 h 18 min
Approx.
5 h 12 min
Features of the Input/Output unit
Other features
AJ-HPX2700G-VQT1V27_eng.book 11 ページ ２００８年９月２日 火曜日 午後５時４３分