Pyramid Car Audio CDR-38DX - Manual (Page 5)

Page 03 Page 06
1
3
4
5
2
2
5
8
(Fig. 3)
1
2
6
5
4
3
7
(Fig. 2)
NOTE: The mounting box, outer trim ring, and half-sleeve are not used for method B installation.
1. Dashboard
2. Nut (5mm)
3. Spring Washer
4. Screw (5 x 25mm)
5. Screw 6. Strap
Be sure to use the strap to secure the
back of the unit in place. The strap can
be bent by hand to the desired angle.
7. Plain Washer
8. Fix the springs on each side.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on the
sides of the unit
Fastening the unit to the factory radio
mounting bracket.
1. Select a position where the screw holes of
the bracket and the screw holes of the
main unit become aligned (are fitted), and
tighten the screws at 2 places on each
side. Use either truss screws
(5 x 5mm) or flush surface screws (4 x
5mm), depending on the shape of the
screw holes in the bracket.
2. Screw
3. Factory radio mounting bracket
4. Dashboard or Console
5. Hook (Remove this part)
NOTE: If Press RESET button (21), the unit can't work yet, please use a cotton swab soaked in isopropyl
alcohol to clean the socket on the back of the front panel.
SELECT MODE
Press SEL button (3) to change audio
mode through volume, bass, treble, balance
mode. Use VOL Up (4) and VOL Down (5)
button to adjust the selected mode. When
mode has not been adjusted for several
seconds, display returns to normal radio or
CD display.
VOLUME
Adjust volume level by using VOL Up (4)
and VOL Down (5) buttons.
BASS
Press SEL button (3) one time. Adjust bass
level by using VOL Up (4) and VOL Down
(5) buttons.
TREBLE
Press SEL button (3) two times. Adjust
treble level by using VOL Up (4) and VOL
Down (5) buttons.
BALANCE
Press SEL button (3) three times. Adjust
sound balance between left and right
speakers by using VOL Up (4) and VOL
Down (5) buttons.
FADER (optional)
Press SEL button (3) four times. Adjust
sound balance between front and rear
speakers by using VOL Up (4) and VOL
Down (5) buttons.
MUTE
Press MUTE button (6) to mute down sound.
Press it again to release this mode and recover
previous volume level.
CD MODE/RADIO MODE
During CD operation, Press BND button (10)
to switch to radio mode. During radio operation,
when a compact disc is inserted in the Disc
Slot (16), Press Play/Pause button (14) to
switch to CD mode and start playing.
EQUALIZATION
Press EQ button (7) to turn to equalization
function and to select desired audio mode.
There are four kinds of modes as below:
LIQUID CRYSTAL DISPLAY
The LCD (19) can show the current state of
the unit.
FLASHING LED
If the front panel is not on the main unit, LED
(20) will be flashing.
RESET BUTTON FUNCTION
RESET button (21) is placed on the housing
and must be activated with either a ballpoint
pen or thin metal object. The RESET button
(21) is to be activated for the following
reasons:
· Initial installation of the unit when all wring is
completed.
· All the function buttons do not operate.
· Error symbol on the display.
BAL
(Volume)
VOL BAS TRE BAL FAD
(Volume) (Bass) (Treble) (Balance) (Fader)
OPTIONAL:
VOL BAS TRE
(Bass) (Treble) (Balance)
EQ/OFF POP CLASSIC ROCK
03 GENERAL OPERATIONS 01 INSTALLATION