Poulan 961970005 - Manual (Page 17)

17
BELT KEEPER
IDLER ARM
SQUARE
HOLE
BOLT LOCK
WASHER
TRACTION DRIVE BELT
CLUTCHING
IDLER ARM
BRACKET
AUGER
BELT
FLAT WASHER
AUGER PULLEY
AUGER
HOUSING
FRAME
ENGINE
PULLEY
LOCKWASHER
BOLT
FIG. 23
SERVICE AND ADJUSTMENTS
1. REMOVE GASOLINE FROM FUEL TANK - Drain gaso-
line from fuel tank into a suitable container, out doors,
away from fi re or fl ame. Wipe up any spilled gasoline.
2. REMOVE DISCHARGE CHUTE - Loosen locknut
se cur ing chute rotator head to mounting bracket only
enough to allow chute rotator head to be raised and
dis charge chute to be removed from snow thrower.
3. REMOVE BELT COVER - See “TO REMOVE BELT
COVER” in this section of this manual.
4. REMOVE ENGINE PULLEY - Remove bolt, lock wash er
and fl at washer securing pulley to engine crankshaft.
Remove outside (auger) pulley only from crank shaft.
5. SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
re move the two (2) bolts and lock washers holding
auger housing and frame together.
WARNING: As the last bolt is removed,
have your assistant carefully lower the
han dles down to the ground.
6. REMOVE AUGER BELT from around pulley.
7. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER
and remove traction drive belt from around pulleys.
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into
the square hole in idler arm and rotate ratchet clockwise
to relieve tension.
8. With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
9. Place auger belt around and inside the groove of auger
pulley only.
10. While your assistant slowly raises handles to rejoin
the auger hous ing and frame assembly, pull up on the
auger belt and squeeze sides together above pulley
so belt is fully seated in groove of pulley.
11. Bring snow thrower completely together and check
carefully for proper routing of belts. If auger belt has
become dislodged from the pulley (by catching the idler
arm bracket while bringing snow thrower together),
separate the snow thrower and re peat step 10. Belt
must be fully seated in pulley groove when bring ing
the snow thrower together.
WARNING: Belt replacement requires
separation of the snow thrower. While
separating the auger housing from the
frame assembly, it is important that an
assistant stand in the operating po si tion
and hold the snow thrower han dles. Se-
rious personal injury and/or damage to
the unit could occur if the snow thrower
should fall during the belt chang
ing
process.
TO REMOVE WHEELS (See Fig. 24)
• Remove the klik pin and remove wheel from axle.
IMPORTANT: When installing wheel, be sure to use the axle
hole closest to the end of the shaft –
do not use the hole
in the wheel hub (if equipped). Inner hole in axle and hole
in wheel hub are not used for your model snow thrower.
NOTE: To seal punctures or prevent fl at tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and cor ro sion.
FRAME
ASSEMBLY AUGER
HOUS ING
HANDLES
12. Install the two (2) hex bolts and lock washers and
tighten securely.
13. INSTALL ENGINE PULLEY - Place belt in pulley groove
and slide pulley on crankshaft. Install fl at washer, lock-
washer and bolt and tighten securely (30-35 ft. lbs.
torque). Make sure belt is inside belt keeper.
14. INSTALL BELT COVER and two (2) screws. Tighten
securely.
15. INSTALL DISCHARGE CHUTE – See “INSTALL DIS-
CHARGE CHUTE / CHUTE ROTATER HEAD” in the
As sem bly / Pre-Operation section of this manual.
AXLE
KLIK PIN (INSTALL
IN OUTER HOLE
OF AXLE ONLY) OUTER HOLE
WHEEL HUB WHEEL
FIG. 24