Pioneer XM SATELLITE DIGITAL TUNER GEX-P910XM - Manual (Page 2)

Before You Start
Head unit group 3
Function Button Operation
Source switching SOURCE :Select
Select the channel or :Select
Changing the band BAND :Select
Switching the DISPLAY :Select
display
Scrolling the DISPLAY :Scroll
display (hold for 2
seconds)
Display the MENUS A.MENU :Display
Preset memory 1. or :Select number
(P.CH MEMORY) 2. A.MENU :Memory
Direct recall 1. or :Select number
(P.CH RECALL) 2. A.MENU :Recall
Switching the or :Select
channel select
mode (CH MODE)
Select the category or :Select
(Channel category
select mode)
En
Before You Start
Head unit group 2
When using this unit with these head units,
operate while referring to the head unit group
2 function compatibility chart.
• These head units control this unit as an
external unit.
DEH-P90HDD* DEH-P4400
DEH-P440 DEH-P44
FH-P4100
Head unit group 3
When using this unit with these head units,
operate while referring to the head unit group
3 function compatibility chart.
AVH-P6400CD AVH-P6400
Function compatibility charts
Operate using the same buttons on the head
unit itself or the remote control.
Head unit group 2
Function Button Operation
Source switching SOURCE :Select
Select the channel or :Select
Changing the band BAND :Select
Preset memory 1–6 :Memory
(hold for 2
seconds)
Direct recall 1–6 :Recall
Sequential recall or :Recall
(Channel number
select mode)
Select the category or :Select
(Channel category
select mode)
Entering the FUNCTION :Select
function menu
(See “Introduction
of advanced tuner
operation”.)
Switching the or :Select
display (FUNC1)
Scrolling the or :Scroll
display (FUNC1) (hold for 2
seconds)
Scrolling the DISPLAY :Scroll
display (hold for 2
seconds)
Switching the or :Select
channel select
mode (FUNC2)
En
Before You Start Before You Start
• Keep this manual handy as a reference for
operating procedures and precautions.
• Always keep the volume low enough so
you can hear sounds outside of the car.
• Protect this product from moisture.
• If the battery is disconnected or
discharged, the preset memory will be
erased and must be reprogrammed.
After-sales service for
Pioneer products
Please contact the dealer or distributor from
where you purchased this unit for after-sales
service (including warranty conditions) or
any other information. In case the necessary
information is not available, please contact
the company listed below:
Please do not ship your unit to the company
at the addresses listed below for repair with-
out advance contact.
For warranty information please see the
Limited Warranty sheet included with this
unit.
Product registration
Visit us at the following site:
1 Register your product. We will keep the
details of your purchase on file to help you
refer to this information in the event of an
insurance claim such as loss or theft.
2 Receive updates on the latest products
and technologies.
3 Download owner’s manuals, order prod-
uct catalogues, research new products,
and much more.
Operating with different
head units
Operate this unit (for XM reception) with the
connected head unit. For illustration, instruc-
tions in this manual use the “DEH-P6400” as
an example of head unit.
• When using a remote control, you can
operate these head units marked with * in
the same way as the “DEH-P6400”. For
details concerning operation with the
head unit itself, refer to the head unit’s
operation manual.
Head unit group 1
Operation when using the following head
unit is the same as with the “DEH-P6400”,
operate following the instructions in this
manual.
DEH-P9400MP* DEH-P940MP*
DEH-P8400MP DEH-P840MP
DEH-P7400MP DEH-P740MP
DEH-P640 DVH-P7000
U.S.A.
Pioneer Electronics (USA), Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
Important
The serial number of this device is located on
the bottom of this unit. For your own security
and convenience, be sure to record this num-
ber on the enclosed warranty card.
Resetting the microproces-
sor
The microprocessor must be reset under the
following conditions:
• Prior to using this unit for the first time
after installation
• If the unit fails to operate properly
• When strange or incorrect messages
appear on the display
Press RESET on the unit with a pen tip
or other pointed instrument.
RESET button
Precautions
This equipment has been tested and
found to comply with the limits for a class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio com-
munications. However, there is no guar-
antee that interference will not occur in a
particular installation. If this equipment
does cause harmful interference to radio
or television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet
on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced
radio/TV technician for help.
Information to User
Alteration or modifications carried out
without appropriate authorization may
invalidate the user’s right to operate the
equipment.
En En