NuTone AVD50N - Manual (Page 2)

®
Page 
MODELS AVD40N • AVD40KN • AVD40WN
AVD45N • AVD45KN • AVD45WN • AVD50N
OPERATING INSTRUCTION
(Fig. 3)
Control Panel (AVD45 and AVD50 Series)
SAFETY SWITCH
The Ironing Board depresses this switch when placed in its storage position.
This disconnects all power to the ironing center controls.
TIMER
Work Lamp, Pilot Light and Receptacle are powered ONLY when timer is set.
Set the amount of time you will be ironing by turning the knob clockwise. The
timer can be manually turned to “0” (Off) at any time. Turn to “0” (Off) position
when not in use.
PILOT LIGHT
When light is lit, it shows that the timer is set and that the power is “ON”.
WORK LAMP
The lamp will come on when the timer is set. A 40 watt max bulb is recom-
mended.
ELECTRICAL RECEPTACLE
The Ironing Center is equipped with 3-prong grounded receptacle.
CAUTION: Make sure your iron’s power cord does not interfere with operation
of the SAFETY SWITCH when board is being placed in its storage position.
CABINET DOOR
(Fig. 4)
NOTE: Hinges, and hardware are supplied with all units. Doors are included with
AVD40KN, AVD40WN, AVD45KN, and AVD45WN models. Decorative doors
may be purchased separately for AVD40N, AVD45N and AVD50N models.
Maximum weight of door must not exceed 25 lbs. (See Service Parts List)
1. MOUNTING THE CABINET DOOR
Door may be hinged from either side of the cabinet. Both sides of the cabinet
has pre-punched holes.
Use two hinges (supplied) to fix door to the cabinet. Hinges should be placed
on top and bottom section of the cabinet.
Attach the hinge to cabinet and door using the screws supplied.
Use the decorative plugs (supplied) to cover the remaining pre-punched
holes.
① Flat Head, #6 x 1/2” - Door to Hinge & Hinge to Cabinet
② Pan Head, #6 x 3/8” - Magnetic Catch to Cabinet
③ Flat Head, #5 x 3/8” - Strike Plate to Door
2. INSTALLING MAGNETIC CATCH
Magnetic catch is attached opposite the hinge.
Attachment position is located on the top section of the cabinet and the door.
Attach the magnetic catch 2A onto cabinet using the screws supplied.
Attach the strike plate 2B onto door in line with magnetic catches using the
screw (supplied).
3. LAMP REPLACEMENT
Ensure the power is switched off (Timer is on “0” (Off) position).
Insert small screwdriver or slim knife (as shown), ease catch to side and slip
out diffuser.
Replace lamp (40 watt max).
Slide diffuser back into aperture and “click” into place.
IRONING BOARD HEIGHT ADJUSTMENT
(Fig. 5)
MODEL AVD50N
IMPORTANT: Remove the plastic shipping locks from each side of the board
pivot.
The Ironing Board has three working heights, to adjust the board:
1. Lower board to the first operating position(lowest position).
2. Hold the board with one hand (NOT BY THE NOSE) and support the pivot rod
with the other hand.
3. Adjust the Ironing board to the desired position by lifting the board (NOT BY THE
NOSE) and moving it to the path of height adjust bracket.
NOTE: in order to store the Ironing board, it must be on its lowest position.
MAINTENANCE
IRONING CENTER BOARD IS FITTED WITH
HEAT RESISTANT COVER. TO AVOID DAM-
AGE TO THE COVER
DO NOT WASH THE COVER
The laminated surface of the unit may be
wiped clean with non-abrasive household
cleaner.
Fig. 3
Fig. 4
Fig. 5
PLASTIC SHIP-
PING LOCKS