Installation instructions – NEC RIH-3267 User Manual
Page 21
4. Connecting of the Cable
Outdoor Unit
Indoor Unit
1). Remove the access door from the unit by loosening
Connect the power connecting cord to the indoor unit
by connecting the wires to the terminals on the control
board individually in accordance with the outdoor unit
connection.
the screw. Connect the wires to the terminals on the
control board individually as the following.
2). Secure the power connecting cord onto the control
board with cable clamp.
3). Reinstall the access door to the original position
with the screw.
Chassis
Cabinet
Front panel
Capacity (Btu/h)
9K
H07RN-F
H05VV-F
H05VV-F
H07RN-F
12K
Power connecting cord
Power cord
Type
Type
Normal cross
- sectional area
Normal cross
- sectional area
Cable Specifications
Note: For some models, it is necessary to remove the cabinet to
connect to indoor unit terminal.
Terminal (inside)
Access door
Terminal(inside)
Indoor unit
Outdoor unit
Installation instructions
Caution:
1. Never fail to have an individual power circuit specifically for the air conditioner. As for the method of
wiring, refer to the circuit diagram posted on the inside of the access door .
2.Comfirm that the cable thickness is as specified in the power source specification.
(See the cable specification table below)
3.Check the wires and make sure that they are all tightly fastened after cable connection.
4. Be sure to install an earth leakage circuit breaker in wet or moist area.
1.5mm X4
2
1.5mm X4
2
1.5mm
2
X3
1.5mm
2
X3
T he figures in th is manual are based on the external
view of a standard model. Consequently, the shape
may differ from that of the air conditioner you have
selected.
19
Attention:
Accessibility to the plug must be guaranteed even after the installation of the appliance to disconnect
it in case of need. If not possible, connect appliance to a double-pole switching device with contact
separation of at least 3 mm placed in an accessible position even after installation.
2
4. Connecting of the Cable
Outdoor Unit
Indoor Unit
1). Remove the access door from the unit by loosening
Connect the power connecting cord to the indoor unit
by connecting the wires to the terminals on the control
board individually in accordance with the outdoor unit
connection.
the screw. Connect the wires to the terminals on the
control board individually as the following.
2). Secure the power connecting cord onto the control
board with cable clamp.
3). Reinstall the access door to the original position
with the screw.
Chassis
Cabinet
Front panel
Capacity (Btu/h)
9K
H07RN-F
H05VV-F
H05VV-F
H07RN-F
12K
Power connecting cord
Power cord
Type
Type
Normal cross
- sectional area
Normal cross
- sectional area
Cable Specifications
Note: For some models, it is necessary to remove the cabinet to
connect to indoor unit terminal.
Terminal (inside)
Access door
Terminal(inside)
Indoor unit
Outdoor unit
Installation instructions
Caution:
1. Never fail to have an individual power circuit specifically for the air conditioner. As for the method of
wiring, refer to the circuit diagram posted on the inside of the access door .
2.Comfirm that the cable thickness is as specified in the power source specification.
(See the cable specification table below)
3.Check the wires and make sure that they are all tightly fastened after cable connection.
4. Be sure to install an earth leakage circuit breaker in wet or moist area.
1.5mm X4
2
1.5mm X4
2
1.5mm
2
X3
1.5mm
2
X3
T he figures in th is manual are based on the external
view of a standard model. Consequently, the shape
may differ from that of the air conditioner you have
selected.
19
Attention:
Accessibility to the plug must be guaranteed even after the installation of the appliance to disconnect
it in case of need. If not possible, connect appliance to a double-pole switching device with contact
separation of at least 3 mm placed in an accessible position even after installation.
2
4. Connecting of the Cable
Outdoor Unit
Indoor Unit
1). Remove the access door from the unit by loosening
Connect the power connecting cord to the indoor unit
by connecting the wires to the terminals on the control
board individually in accordance with the outdoor unit
connection.
the screw. Connect the wires to the terminals on the
control board individually as the following.
2). Secure the power connecting cord onto the control
board with cable clamp.
3). Reinstall the access door to the original position
with the screw.
Chassis
Cabinet
Front panel
Capacity (Btu/h)
9K
H07RN-F
H05VV-F
H05VV-F
H07RN-F
12K
Power connecting cord
Power cord
Type
Type
Normal cross
- sectional area
Normal cross
- sectional area
Cable Specifications
Note: For some models, it is necessary to remove the cabinet to
connect to indoor unit terminal.
Terminal (inside)
Access door
Terminal(inside)
Indoor unit
Outdoor unit
Installation instructions
Caution:
1. Never fail to have an individual power circuit specifically for the air conditioner. As for the method of
wiring, refer to the circuit diagram posted on the inside of the access door .
2.Comfirm that the cable thickness is as specified in the power source specification.
(See the cable specification table below)
3.Check the wires and make sure that they are all tightly fastened after cable connection.
4. Be sure to install an earth leakage circuit breaker in wet or moist area.
1.5mm X4
2
1.5mm X4
2
1.5mm
2
X3
1.5mm
2
X3
T he figures in th is manual are based on the external
view of a standard model. Consequently, the shape
may differ from that of the air conditioner you have
selected.
19
Attention:
Accessibility to the plug must be guaranteed even after the installation of the appliance to disconnect
it in case of need. If not possible, connect appliance to a double-pole switching device with contact
separation of at least 3 mm placed in an accessible position even after installation.
2
Note: The c able will be pr ov id ed or purchase d by cus tomer.
PDF created with pdfFactory Pro trial versi