Nintendo Aquos LC-32D44U - Manual (Page 20)

20
EZ Setup
You can run EZ Setup again, even after setting up the
preset channels.
Language: Select from among 3 languages (English,
French and Spanish).
TV Location: Select "Home" or "Store" for the location
where you plan to install the TV.
If you select "Home", AV MODE is set to "STANDARD".
If you select "Store", AV MODE is set to "DYNAMIC (Fixed)".
In case no remote control signal is received within 30
minutes, AV MODE will change to "DYNAMIC (Fixed)"
automatically.
Air/Cable: Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
CH Search: Channel auto search makes the TV look for
all channels viewable in the set area.
See "Initial Setup" on page 12 for setting each item.
If no channel is found, confi rm the type of connection made
with your TV and try EZ Setup again.
If you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
CH Setup
If initial setup does not memorize all the channels in
your region, follow the instructions below to manually
memorize the channels.
Air/Cable: Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
CH Search: Channel auto search makes the TV look for
all channels viewable in the set area.
CH Memory: You can select the channels to skip in each
ANALOG (Air), ANALOG (Cable), DIGITAL (Air) and
DIGITAL (Cable).
On: Skips channels. (Channel selection disabled using CH
r/s.)
Off: Does not skip channels. (Channel selection enabled using
CHr/s.)
See "Initial Setup" on page 12 for setting each item.
If no channel is found, confi rm the type of connection made
with your TV and try channel search again.
If you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
Antenna Setup - DIGITAL
In order to receive digital air broadcasts, you need
a digital broadcast antenna. You can confi rm the
antenna confi guration through the "Antenna Setup -
DIGITAL" screen. If necessary, adjust the direction of
the antenna to obtain the maximum signal strength.
Signal Strength: The signal strength of DIGITAL channel
is displayed. The signal information is based on the
current channel.
Channel Strength: Input the 2-digit channel number
to check the signal strength of the selected channel.
Make sure the signal is strong enough for each
channel.
This function is available for DIGITAL (Air) only.
•
•
•
•
•
•
•
•
•
On-Screen Display Menu
Power Control Menu
Power control setting allows you to save energy.
No Signal Off
No Operation Off
[Disable]
[Disable]
Power Control
Example
1 Press MENU to display the MENU screen, and then
press c/d to select "Power Control".
2 Press a/b to select a "No Signal Off" or "No
Operation Off", and then press ENTER.
3 Press c/d to select "Enable", and then press
ENTER.
4 Press MENU to exit.
No Signal Off
When set to"Enable", the power will automatically shut
down if there is no signal for 15 minutes.
Five minutes before the power shuts down, the remaining
time displays every minute.
"Disable" is the factory preset value.
When a TV program fi nishes, this function may not operate.
No Operation Off
When set to "Enable", the power will automatically shut
down if there is no operation for 3 hours.
Five minutes before the power shuts down, the remaining
time displays every minute.
"Disable" is the factory preset value.
Setup Menu
CH Setup
Antenna Setup-DIGITAL
EZ Setup
Input Skip
Parental CTRL
Position
Language
Reset
[English]
Setup
Example
1 Press MENU to display the MENU screen, and then
press c/d to select "Setup".
2 Press a/b to select a specifi c adjustment item,
and then press ENTER.
When you select "EZ Setup", "CH Setup", "Parental
CTRL" and "Reset", you can enter the 4-digit secret
number here. See page 22 for setting a secret number.
3 Press a/b (or c/d) to select the desired setting,
and then press ENTER.
4 Press MENU to exit.
•
•
•
•
•
•