RIDGID K6200 - Manual (Page 7)

K-6200 Drain Cleaning Machine
Machine Assembly
WARNING
To prevent serious injury, proper assembly of the
Drain Cleaner is required. The following procedures
should be followed:
Instructions For Installing Handles
Remove the two (2) screws from handle. Loosen two (2)
“T” handles and slide handle into the frame (Figure 5).
Replace the two screws in the handle to prevent it slid-
ing out of the frame. Adjust the handle to the desired
height and firmly tighten the “T” handles to lock the
handle in place.
Instructions For Installing Cable
Do not remove bands or staples from cable
shipping carton. Cable is under tension and will whip,
causing injury.
Retrieve end of cable through the center hole of carton and
remove enough cable to connect with drum pigtail. Connect
to pigtail by sliding cable couplings together and turning
screwdriver slot in coupler 180°. Couplings are in locked
position when hash mark is on opposite side of screwdriver
slot as shown in Figure 3. Feed cable into drum.
Ridge Tool Company 5
CAUTION
Catalog
No.
92460
92465
92470
43647
32737
58192
95762
95757
95752
95747
92555
44122
Model
No.
C-25
C-26
C-27
C-24
C-27HC
C-24HC
C-25 IW
C-26 IW
C-27 IW
C-24 IW
T-458
—
Cables and Flexible Trap Leaders
5 /
8
″ (16mm)
5 / 8 ″ (16mm)
5 /
8
″ IW (16mm)
Description
25 ′ I.C. Cable (7,6m)
50 ′ I.C. Cable (15,2m)
75 ′ I.C. Cable (22,9m)
100 ′ I.C. Cable (30,5m)
75 ′ Hollow-Core (22,9m)
100 ′ Hollow-Core (30,5m)
25 ′ I.W. Cable (7,6m)
50 ′ I.W. Cable (15,2m)
75 ′ I.W. Cable (22,9m)
100 ′ I.W. Cable (30,5m)
5 /
8
″ x 2 ′ Leader
5 /
8
″ Pigtail
Tools and Replacement Blades — Fits C-24,
C-25, C-26, C-27,C-24 IW, C25 IW, C-26 IW,
C-27 IW, C-24HC, C-27HC
Catalog
No.
92485
92490
92495
92500
92505
51762
92510
92515
92520
92525
92530
92535
92540
92545
92550
Model
No.
T-403
T-404
T-406
T-407
T-408
T-409
T-411
T-412
T-413
T-414
T-416
T-432
T-433
T-434
T-436
Blade(s)
92835
92840
92850
—
92890
—
92815
92820
92825
92830
92855
92860
92865
92870
92875
Holder*
92900
92900
92915
—
92915
—
92905
92905
92910
92910
92910
92895
92895
92895
92895
Description
P-Trap Cutter, 3 ″
P-Trap Cutter, 3 1 /
2
″
Spear Blade
Retrieving Auger
Sawtooth Cutter
H-D Bulb Auger
Double Cutter, 2 ″
Double Cutter, 2 1 /
2
″
Double Cutter, 3 ″
Double Cutter, 4 ″
Double Cutter, 6 ″
3-Blade Cutter, 2 ″
3-Blade Cutter, 3 ″
3-Blade Cutter, 4 ″
3-Blade Cutter, 6 ″
Replacement
Fastener*
Blade
Blade
Holder
Coupling*
Figure 2 – Tool Assembly
QUICK-CONNECT CABLE & TOOLS
Rotate pin one-half turn in either direction to
quickly add cable or tools.
Hash Mark
(Locked position)
Screwdriver Slot
Hash Mark
(Un-locked position)
Screwdriver Slot
LOCKED
Hash mark CLOSED aligned with L stamped on coupling.
UNLOCKED
Hash mark OPEN aligned opposite L stamped on coupling.
Coupling features stainless steel pin and spring: eliminates need for
punches, stands, or expansion pins.
Figure 3 – Disconnecting/Connecting Cable to Pigtail or
Tool
* Identifies components
included with holder