Radio Shack 42-4058 - Manual (Page 8)

Using SP
LI
T
8
2. Repeatedly press + or – or enter a
number using the number buttons to
select the equalizer type you want.
The equalizer type (
IjWdZWhZ IjWdZWhZ IjWdZWhZ IjWdZWhZ
,
8Wii ! 8Wii ! 8Wii ! 8Wii !
,
Jh[Xb[ ! Jh[Xb[ ! Jh[Xb[ ! Jh[Xb[ !
,
BekZd[ii BekZd[ii BekZd[ii BekZd[ii
,
C[bbem C[bbem C[bbem C[bbem
,
8h_]^j 8h_]^j 8h_]^j 8h_]^j
,
HeYa HeYa HeYa HeYa
,
:WdY[ :WdY[ :WdY[ :WdY[
,
@Wpp @Wpp @Wpp @Wpp
, or
9bWii_Y 9bWii_Y 9bWii_Y 9bWii_Y
) appears. The bar
graph on the display shows the
frequency response of the type that
appears.
Press H ( EXIT ) or EQUALIZER to exit the
equalizer setting screen.
# &,756+0) 6*' ) #+0
1. After selecting the equalizer type, press
G ( ENTER ).
2. Repeatedly press I or J ( CURSOR ) to
select the band you want to adjust (
Bem Bem Bem Bem
,
C_Z Bem C_Z Bem C_Z Bem C_Z Bem
,
C_Z >_]^ C_Z >_]^ C_Z >_]^ C_Z >_]^
, or
>_]^ >_]^ >_]^ >_]^
). The bar
graphs for the corresponding frequency
range flash.
3. Repeatedly press + or – or enter a
number using the number buttons to
make the adjustment for the band you
want. You can adjust within the range of
–12 to +12. The bar graphs change in
magnitude as you adjust.
4. Press H ( EXIT ) to return to the equalizer
type selection screen, then press
EQUALIZER to exit the equalizer mode.
±
75+0) 52.+6
The SPLIT feature lets you play two different
tones on opposite ends of the keyboard, so
the low-end keys play one tone, and the
high-end keys play another. The main tone
sounds in Channel 1 and the split tone
sounds in Channel 3. You can use the mixer
function to change the volume or other
settings in each channel. See “Using the
Mixer” on Page 12. You can change the split
point at any time.
1. Press TONE.
2. Use the number buttons to enter the
three-digit number for the tone you want
the high-end keys to play.
3. Press SPLIT . The SPLIT indicator
appears.
4. Enter the three-digit number for the
tone you want the low-end keys to play.
5. Hold down SPLIT , and press the key
where you want the high-end tones to
begin. The selected key’s name
appears.
For example, if you set the split point to
be F below middle C,
<) <) <) <) appears. ±
6. Play both the low and high-end keys to
hear the selected split tones.
To select a different low-end tone , enter
the three-digit number for the new low-
end tone while the SPLIT indicator
appears.
To select a different high-end tone ,
press SPLIT to turn off its indicator, then
enter the three-digit number for the new
high-end tone. Then press
SPLIT again
so the SPLIT indicator appears.
To cancel SPLIT , repeatedly press
SPLIT until its indicator disappears. ±
75+0) .#;'4
The keyboard lets you play two different
preset tones at the same time, creating a
“layered” effect when you press one key.
The first tone you select is called the
base
tone and the second tone is called the layer
tone .
1. Press TONE .
2. Enter the three-digit number for the
base tone then press LAYER . The
LAYER indicator appears.
3. Enter the three-digit number for the
layer tone.
4. Play the keyboard to hear the selected
layered tones.
To select a different layer tone , enter
the three-digit number for the new layer
tone while the LAYER indicator
appears.
To select a different base tone , press
LAYER to turn off its indicator, then enter
the three-digit number for the new base
tone. Then press
LAYER again so the
LAYER indicator appears.
To cancel LAYER , repeatedly press
LAYER until its indicator disappears. ±
75+0) 52.+6 #0& .#;'4 61)'6*'4
You can combine the split and layer
features, so you can play one layered
combination of tones on the low-end keys
and another on the high-end keys. 1. If the SPLIT or LAYER indicator is on,
press SPLIT or LAYER to turn it off.
2. Enter the number for the high-end base
tone on the keypad.
±
016'
±
Adjusting the Gain
Gain settings apply only to the current
equalizer type. When you change the
equalizer type, the default gain settings for the
newly selected equalizer type take effect.
Using Split
• If SPLIT is on when you turn off the
keyboard, it remains on the next time you
turn the keyboard back on.
• When you turn on SPLIT, the last selected
settings appear.
• When you select Concert Chord or
Fingered auto accompaniment, the
accompaniment keyboard range is shifted
to the split point you set.
Using Layer
• If LAYER is on when you turn off the
keyboard, LAYER will still be on the next
time you turn on the keyboard.
• When you turn on LAYER, the previous
tone settings appear.