ROTEL Surround Sound Receiver RSX-1055 - Manual (Page 33)

33
OTHER OPTIONS Menu
OTHER OPTIONS
RECORD: CD
DYNAMIC: Max
MULTI INPUT: Off
CINEMA EQ: Off
POWER: Direct
OSD: On
LANGUAGE: ENGLISH
ENT KEY=MAIN MENU UP KEY=up
+/– KEY=change DWN KEY=down
This menu, accessed from the MAIN menu,
provides access to a several miscellaneous
settings as follows:
RECORD: Select a signal for the record out-
puts by choosing one of the input sources.
DYNAMIC: steps through the three dynamic
range settings available in digital modes:
• MAX (no compression/full dynamic range)
• MID (moderate compression)
• MIN (full compression/minimum dynamic
range).
MULTI INPUT: determines whether the MULTI
channel input is turned ON or OFF.
CINEMA EQ: determines if a special equal-
ization setting is turned ON or OFF. This equal-
ization may be desirable for playback of movie
source material to compensate for the acous-
tic differences between a commercial cinema
and a home theater environment. The CIN-
EMA EQ setting can also be changed using
the FILTER button on the remote.
POWER: This setting determines how the
RSX-1055 powers up. With the default DIRECT
setting, the unit is fully activated when AC power
is applied and the front-panel POWER button
is pressed in; however, it may be put in
STANDBY mode using the remote POWER
button. With the STANDBY setting, the unit pow-
ers up in standby mode when AC is applied
and the front-panel POWER button is in the
ON position. The unit must be activated us-
ing the remote control POWER button. In AL-
WAYS-ON mode, the unit remains fully active
whenever AC is present and the front-panel
POWER button is pressed in; the remote
POWER button is disabled and the unit can-
not be put in standby mode.
OSD: Determines whether the ON-SCREEN
DISPLAYS are shown on your TV monitor dur-
ing operation.
LANGUAGE: Selects a language for all of
the ON-SCREEN MENUS.
Change settings on the OTHER OPTIONS menu
by highlighting the desired line using the UP/
DOWN buttons and using the +/– buttons to
step through the available settings. To return
to the MAIN menu, press the ENTER button.
Press the MENU key on the remote to cancel
the display and return to normal operation.
DEFAULT SETUP Menu
DEFAULT SETUP
TUNER SETTING: N. AMERICA
REDIRECT: FRONT
FACTORY DEFAULT: No
USER DEFAULT: No
USER DEFAULT SET: No
ENT KEY=MAIN MENU UP KEY=up
+/– KEY=change DWN KEY=down
DEFAULT SETUP
TUNER SETTING: N. AMERICA
REDIRECT: FRONT
FACTORY DEFAULT: Yes
USER DEFAULT: No
USER DEFAULT SET: No
ENT KEY=Exec. UP KEY=up
+/– KEY=change DWN KEY=down
The DEFAULT SETUP menu provides access to
five functions:
• Restoring all features and settings to the
original FACTORY DEFAULT settings.
• Changing the tuning functions and displays
for use in North America or Europe.
• Specifies whether the front left and front
right internal amplifier channels are used
to power front speaker (default setting) or
center back speakers.
• Memorizing a custom group of settings as
a USER DEFAULT.
• Activating the USER DEFAULT settings.
To restore the FACTORY DEFAULT set-
tings: Place the highlight on the FACTORY
DEFAULT line using the UP/DOWN buttons
and use the +/– buttons to change the setting
to YES. The screen will change to a confirma-
tion screen. Press the ENTER button to proceed
with resetting the FACTORY DEFAULT settings.
The unit will power off and then on, with the
factory settings restored. To return to the MAIN
menu without resetting the FACTORY DEFAULT
settings, change the entry to NO and press
the ENTER button.
NOTE : Resetting to factory default settings will
erase all stored settings including delay set-
tings, speaker settings, balance settings, in-
put settings and more. You will lose ALL system
configuration settings. Be certain that you wish
to do so before resetting the factory defaults.
To change the TUNER setting: Place the
highlight on the TUNER SETTING line using
the UP/DOWN buttons and use the +/– but-
tons to change the setting to N. AMERICA or
EUROPE. Then, move the highlight to the FAC-
TORY DEFAULT line and change the setting to
YES as described above. The screen will
change to a confirmation screen. Press the EN-
TER button to proceed with resetting the FAC-
TORY DEFAULT settings and changing the
TUNER SETTING. To return to the MAIN menu
without resetting the FACTORY DEFAULT and
TUNER settings, change the entry to NO and
press the ENTER button.
NOTE
: Changing the default TUNER SETTING
can only done at the same time as restoring
the FACTORY DEFAULT settings. Therefore,
we recommend selecting your default TUNER
SETTING and resetting to the FACTORY DE-
FAULT settings as the first step in configuring
the unit, before you change or memorize any
other configuration settings.
To change the REDIRECT setting: Place
the highlight on the REDIRECT line using the
UP/DOWN buttons and use the +/– buttons
to change the setting to FRONT SP (for pow-
ering front speakers) or CB SP (for powering
center back speakers. If you use the internal
amplifiers to power center back speakers, then
you will need a separate stereo amplifier to
power your front speakers.
English