RF-Link DAV-2450 - Manual (Page 2)

2.Package Contents 4.Setup Guide
1. Connect one end of the BNC cable to the audio and video jacks, and
connect the other end to your source device. (Or BNC-to-RCA adapter to
audio and video jacks first, then connect RCA cable between transmitter
and source device)
2. Connect antenna to transmitter.
3. Connect power adapter to transmitter, then plug in power to an outlet.
4. Turn on power on transmitter.
2.Package Contents Not e: Mak e su re the ON/ OFF swi tch is in the OFF pos ition bef or e co nne ct ion 「 」
Transmitter
Receiver
1. Connect one end of the BNC cable to the audio and video jacks, and
connect the other end to your receiving device. (Or BNC-to-RCA adapter
to audio and video jacks first, then connect RCA cable between receiver
and receiving devices, such as monitor, speaker....)
2. Connect antenna to receiver.
3. Connect power adapter to receiver, then plug in power to an outlet.
4. Turn on power on receiver.
4
Pairing Process
Press the "Pairing" button after both transmitter and receiver are power on,
the "Link" light will flash (it means the transmitter is searching the receiver).
The "Link" light become solid when the pairing process is done and
success.
Note:
Once the first pairing process is successful, there is no need to repeat it
in the future.
If the "Link" light is off after pairing process is successful, it normally
mean there is no connection between transmitter and receiver. Most of
cases it is because the transmission is out of the range, and the signal
reception is not stable. Please adjust the distance between transmitter
and receiver until it works.
5. Troubleshooting
5
If there is no signal at all
Check cable connections from the transmitter to the source device, and
the receiver to the receiving device.
Make sure power of all devices are on.
Switch all power off and on again to ensure everything is functioning
well.
If the signal is poor, or there is an interference
Change transmitter's location.
Double check if there is a microwave oven in use, and if it is in the path
between transmitter and receiver. If yes, please either remove it or turn
it off.
Make sure the transmission is within its operating range (up to 300
meters with clear line of sight).
Care and Maintenance
Keep all parts and accessories out the reach of young children.
Do not attempt to open the case.
Keep dry. Precipitation, humidity, and liquids contain minerals that will corrode
electronic circuits.
Do not use or store the unit in dusty, dirty areas.
Do not store the unit in high temperature area. It can shorten the life of electronic
components, and warp or melt certain plastic parts.
Do not store the unit in cold temperature area. When the unit warms up (to its normal
temperature), moisture can form inside the case, which may cause damage to
electronic circuit boards.
Do not drop, knock, or shake the unit. Rough handling can break internal circuit
boards.
Do not use chemicals, cleaning solvents, or strong detergents when cleaning.
Only use the power adapter included in the package to operate the unit.
Try not overload electrical outlets or extension cords as this can result in fire or electric
shock.
6
WEEE Directive & Product Disposal
At the end of its serviceable life, this product should
not be treated as household or general waste. It should
be handed over to the applicable collection point for
the recycling of electrical and electronic equipment, or
returned to the supplier for disposal.
FCC Statement
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Note:
This equipment has been tested and found to comply with the limits regulated
by FCC and CE. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to
radio communications. The change or modifcations not expressly approved by
the party responsible for compliance could void the user’s authority to operate
the equipment. To comply with the FCC RF exposure compliance requirements,
no change to the antenna or the device is permitted. Any change to the antenna
or the device could result in the device exceeding the RF exposure requirements
and void user’s authority to operate the device.
408-000666-00
TTD-B2450T
TTD-B2450R