Royal Sovereign RSC-1650 - Manual (Page 5)

RSC-1650H/C/HR
Speed# Speed(Ft/min,M/min)
1 4(1.2)
2 6(1.7)
3 7(2.2)
4 9(2.6)
5 10(3.1)
6 12(3.6)
7 14(4.2)
8 15(4.5)
9 16(5.0)
RSC Series
8 7
7. SPEED AND TEMPERATURE SETTINGS
8. ROLLER NIP SETTING
R S C - 1 6 5 0 H R S C - 1 6 5 0 H R
T e m p . # T e m p e r a t u r e ( ? ? ? ? ? ? ? ? ? ? ? ? W2@@6X ? ?W&(MI')X? ? ?7@HeN@1? ? ?@@?e?@@? ? ?3@LeJ@5? ? ?V')KO&(Y? ? V4@@0Y ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?
F , ? ? ? ? ? ? ? ? ? ? ? ? W2@@6X ? ?W&(MI')X? ? ?7@HeN@1? ? ?@@?e?@@? ? ?3@LeJ@5? ? ?V')KO&(Y? ? V4@@0Y ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?
C ) T e m p e r a t u r e ( ? ? ? ? ? ? ? ? ? ? ? ? W2@@6X ? ?W&(MI')X? ? ?7@HeN@1? ? ?@@?e?@@? ? ?3@LeJ@5? ? ?V')KO&(Y? ? V4@@0Y ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?
F , ? ? ? ? ? ? ? ? ? ? ? ? W2@@6X ? ?W&(MI')X? ? ?7@HeN@1? ? ?@@?e?@@? ? ?3@LeJ@5? ? ?V')KO&(Y? ? V4@@0Y ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?
C )
1 N o H e a t i n g N o H e a t i n g
2 N o H e a t i n g 8 6 ( 3 0 )
3 9 1 ( 3 3 ) 1 1 3 ( 4 5 )
4 9 7 ( 3 6 ) 1 4 0 ( 6 0 )
5 1 0 4 ( 4 0 ) 2 3 0 ( 1 1 0 )
6 1 1 1 ( 4 4 ) 2 3 9 ( 1 1 5 )
7 1 1 5 ( 4 6 ) 2 4 8 ( 1 2 0 )
8 1 1 7 ( 4 7 ) 2 5 7 ( 1 2 5 )
9 1 2 4 ( 5 1 ) 2 6 6 ( 1 3 0 )
It is important to adjust the roller nip settings to the appropriate thickness of the board
being used. Use the guide below to adjust to the correct position.
NO. Inches Metric
(mm)
1 Lamination Lamination
2 1/ 25" 1
3 3/16"~1/4" 5-7
4 3/ 8"~1/2" 10-13
5 3/5" 15
9. USING FOOT PEDAL AND REMOTE CONTROL
USING FOOT PEDAL
USING REMOTE CONTROL
Place the foot pedal on the floor in front of the
machine. Once all correct settings are displayed, you
may use the foot pedal to operate the laminator for
“Hands Free Operation.” To activate the machine,
press the foot pedal once and then release. Repeat
to stop the rollers.
Located on the rear left side of the laminator.
1. PRESS RUN – To activate the rollers.
2. PRESS STOP – To stop the rollers from turning.
3. PRESS REV – To reverse the rollers. Press and
hold the button (useful for jams or misted media).
1 2 3
NOTE: If you don't want to
laminate,please place the
pressure lever to the "Open
position(NO.5)".