STIEBEL ELTRON CS 20 L - Manual (Page 11)

11
English
2. Installation instructions
for the professional
Installation and electrical connection must be
carried out by a qualified installer, under
observance of these installation instructions.
The CS 20 (L) is supplied complete with a
connecting cable.
Only remove the packaging of the unit and
accessories at the place of installation, taking
note of the additional package.
When unpacking, take care to ensure that no
accessories remain behind in the packaging
material.
2.1 Unit design
(see page 3)
1 Thermostat knob
2 Heat output switches
3 Fan ON/OFF switch (CS 20 L only)
4 Air outlet grille
5 Fan air outlet grille (CS 20 L only)
6 Recessed grips
7 Foot
8 Hanging bracket
2.2 Provisions and regulations
This unit are not suitable for rooms
which are subjects to a fire or
explosion risk caused by chemicals, dust,
gases or vapours. In workshops or other
areas in which the odour of waste gases,
oil, petrol, etc. might occur, or in which
work is carried out involving solvents and
chemicals, there is a risk of sustained
odour burdens being engendered, and
possibly of dirt contamination occurring.
See 1.3 Safety instructions!
• The unit may only be fitted on a vertical
wall which is temperature resistant to at
least 80 °C.
• The minimum distances from adjacent
objects must be observed.
• All electrical connection and installation
work is to be carried out in accordance
with the I.E.E Regulations, the provisions of
the appropriate electricity supply
companies, and the relevant national and
regional provisions.
• The unit must not be fitted directly
beneath an electrical wall socket.
• The appliance should be installed such that
the plug is still accessible.
• The unit rating plate is to be noted. The
stated voltage must correspond to the
mains voltage
• If the heating unit is installed in rooms with
a bath and/or a shower, the range of pro-
tection according to the I.E.E. Regulations-
• Before switching on when as a mobile
free-standing unit, both feet must be fitted
to the unit.
1.4 Care and maintenance
If slight brownish discolouration should
appear on the unit housing, this should be
rubbed off as soon as possible with a damp
cloth.
The unit should be cleaned in the cold
condition, using customary cleaning agents.
Abrasive or corrosive cleaning agents should
be avoided.
Do not spray any cleaning sprays into the air
slots. 1.5 Important instruction
Keep these instructions carefully and
pass them on to your successor in
the event of a change in ownership.
In the event of any repair work, hand them
to the qualified installer for his attention.
in conformity with the information on the
unit rating plate - must be taken into account.
• The unit is to be fitted in such a way that
switching and control devices cannot be
touched by anyone in the bath or under
the shower.
• This appliance should not be used in the
vicinity of a bath, shower or swimming pool.
• If the mains connection cable is changed,
this may only be replaced with original
Stiebel Eltron spare parts by a qualified
installer.
2.3 Unit installation
2.3.1 Fitting the feet B
The feet (7), including securing screws, are
supplied with the unit as standard.
Insert the feet with the guide pins - of varia-
ble thickness - into the side sections at the
bottom, and screw tightly. When doing this,
note that in the case of the left-hand foot
(7a), the mains connection cable is fed
through the channel in the foot.
2.3.2 Wall mounting C
(only possible without the feet fitted)
The following action should be taken to
secure the unit:
!
Fix the hanging brackets (8) vertically to
the wall. Use suitable securing materials
(screws, dowels etc.), dependant on the
type of wall.
Observe the minimum distance from the
floor!
! hang the unit onto the hanging brackets
using the vertical recesses in the rear panel
of the unit;
! using a screwdriver, turn the retaining clips
(at the top of the hanging bracket)
clockwise into the unit - the unit is then
secured against unintentional removal.
2.4 Electrical connection
Electrical connection can only be made to an
a.c. 230V ~ 50 Hz supply.
For the purpose of connection, an earthed
socket or unit connection box for permanent
connection should be installed at the side of
the heating unit, at least 10 cm away from it.
2.5 Handover
Explain the functions of the unit to the user.
Draw his or her attention to the safety
instructions, in particular. Hand the operating
and installation instructions to the user.
3. Environment and
recycling
For guarantees please refer to the pespective
terms and conditions of supply for your
country.
The installation, electrical connection
and first operation of this appliance
should be carried out by a qualified installer.
The company does not accept liability for
failure of any goods supplied which accor-
dance with the manufacturer's instructions.
Please help us to protect the environment by
disposing of the packaging in accordance with
the national regulations for waste processing.
4. Guarantee
Type CS 20 CS 20 L
Dimensions H / W / D mm 390 / 600 / 100 390 / 710 / 100
Weight kg 4,8 6,0
Connection 1/N ~ 230 V 50/60 Hz
Output kW 0,75 / 1,25 / 2,0
Temperature adjustment range ºC ca. 5 bis 35
Frost protection ºC ca. 7
Protection class II
Approvals see unit rating plate
Technical data