Ryobi TBBC - Manual (Page 4)

4
RULES FOR SAFE OPERATION
SAFETY WARNINGS FOR GAS
POWERHEADS
• Store fuel only in containers specifically designed and
approved for the storage of such materials.
• Always stop the engine and allow it to cool before
filling the fuel tank. Never remove the cap of the fuel tank,
or add fuel, when the engine is hot. Never operate the
unit without the fuel cap securely in place. Loosen the
fuel tank cap slowly to relieve any pressure in the tank.
• Add fuel in a clean, well-ventilated outdoor area where
there are no sparks or flames. Slowly remove the fuel
cap only after stopping engine. Do not smoke while
fueling or mixing fuel. Wipe up any spilled fuel from the
unit immediately.
• Avoid creating a source of ignition for spilled fuel. Do
not start the engine until fuel vapors dissipate.
• Move the unit at least 30 feet (9.1 m) from the fueling
source and site before starting the engine. Do not
smoke. Keep sparks and open flames away from the
area while adding fuel or operating the unit.
• Squeeze the throttle control and check that it returns
automatically to the idle position. Make all adjustments
or repairs before using the unit.
WHILE OPERATING
• Read and understand all safety warnings before
operating this unit.
• Inspect thoroughly for loose nuts, bolts or damage
before continuing. Repair or replace affected parts as
necessary.
• Wear safety glasses or goggles that meet ANSI Z87.1
standards and are marked as such. Wear ear/hearing
protection when operating this unit. Wear a face or
dust mask if the operation is dusty.
• Wear heavy long pants, boots, gloves and a long
sleeve shirt. Do not wear loose clothing, jewelry, short
pants, sandals or go barefoot. Secure hair above
shoulder level.
• Adjust the J-handle to your size in order to provide the
best grip.
• Use the unit only in daylight or good artificial light.
• Avoid accidental starting. Be in the starting position
whenever pulling the starter rope. The operator and
unit must be in a stable position while starting. Refer
to Starting/Stopping Instructions of the power head
manual.
• Use the right tool. Only use this tool for its intended
purpose.
• Do not overreach. Always keep proper footing and
balance.
• Always hold the unit with both hands when operating.
Keep a firm grip on both handles or grips.
• Keep hands, face, and feet at a distance from all
moving parts.
• Do not operate the engine/motor faster than the speed
needed to cut. Do not run the engine at high speed
when not cutting.
• Always stop the engine when you delay working, or
when you walk from one cutting location to another.
• If you strike or become entangled with a foreign
object, stop the engine immediately and check for
damage. Do not operate before repairing damage. Do
not operate the unit with loose or damaged parts.
Gasoline is highly
flammable, and its
vapors can explode if ignited. Take the
following precautions:
WARNING:
• The TBBC is specifically approved for use with the
following models of attachment-capable trimmers:
Ryobi : Troy-Bilt :
775R TB20CS
750R TB25CS
790R TB25ET
890R TB70SS
TB75SS
Yard Man : TB90BC
YM25 TB425CS
YM75 TB475SS
YM90 TB490BC
YM26BC
Bolens (Canada) :
Cub Cadet : BL26BC
CC2025
CC3075 Yardworks :
CC4025 60-2310-6
CC4075 60-2311-4
CC4090 60-2312-2
• Do not touch the engine, gear housing or muffler.
These parts get extremely hot from operation, even
after the unit is turned off.
• To reduce fire hazard, replace a faulty muffler and
spark arrestor. Keep the engine and muffler free from
grass, leaves, excessive grease or carbon build up.
• Never start or run the unit inside a closed room or
building. Breathing exhaust fumes can be fatal.
Operate this unit only in a well-ventilated outdoor area.