Radio Shack 63-1416 - Manual (Page 2)

2
hold) MIN until the desired minute
appears.
3. Release TIME SET , the set time appears.
5 +)0#. "5 64'0)6* "& '6'%6+10 "
U0&& U0&& U0&& U0&& appears when the clock receives a
signal. The digit left of the colon indicates the
level of signal strength.
Place your clock in a location with strong
signal strength. It is recommended to locate
the clock near a window facing the direction
of Fort Collins, Colorado. If the clock has
poor signal reception or unstable signal
marks, move the clock to another location.
While the clock is receiving, press TIME SET
once to go to the Time display mode. The
clock continues receiving the atomic time.
Press
HOUR/WAVE to enter Signal Strength
display.
While the clock is receiving, if you set the
time or an alarm, the clock stops receiving
immediately.
When receiving cannot be completed at 7
minutes after power up, the clock returns to
the time display with clock
'(0&- '(0&- '(0&- '(0&- am appears
and remote control (RC) receiving continues.
4 '%'+8+0) "6 19'4 " +0&+%#614 "
( +456 " 4'%'26+10 " #(6'4 "
% 100'%6+0) "2 19'4
The clock starts to search for the WWVB
signal and searches for 20 minutes after you
connect it to power.
In optimal conditions, the correct time will be
displayed within 10 minutes
The atomic reception tower icon will keep
blinking when the clock is receiving the
signal.
The static atomic reception tower indicator
indicates successful reception.
The signal is at its maximum strength from
12:00 am to 3:00 am and with minimal radio
interference. In most cases, the clock will not
receive and update its time until this time.
9KVJKP"VJG"HKTUV"5"JQWTU
If your clock fails to receive the signal in the
1st reception after power-up, it will repeat a
20-minute reception sequence every 60
minutes. This operation stops when the time
signal is received
#HVGT"VJG"HKTUV"5"JQWTU"
If no signal can be received within the first
three hours, the clock repeats the reception
every three hours until it receives a signal.
#WVQOCVKE"VKOG"WRFCVG
The clock automatically updates everyday at
01:00 (1:00 a.m.) and 03:00 (3:00 a.m.) and
05:00 (5:00 a.m.). If the automatic time
update fails, it will repeat the update every 3
hours until it is successful in receiving the
signal.
/CPWCN"VKOG"WRFCVG
Manual reception can be started anytime by
pressing
HOUR / WAVE .
The time display changes to Signal Strength
Detection display
U0&&U U0&&U U0&&U U0&&U . The clock will start
to search for the WWVB signal for 20
minutes.
5'66+0)"6*'"#.#4/5
# .#4/ "3" 14 "4
1. Slide ALM to ALM 1 or ALM 2 . The ALM 1
LED lights or the ALM 2 LED lights. ± ± ± ±
2. To set the alarm hour, Press and hold
ALARM/SET and press (or press and
hold) HOUR/WAVE until the desired hour
appears on the display.
3. To set alarm minute, press and hold
ALARM/SET and press (or press and
hold) MIN until the desired minute
appears on the display.
4. Release ALARM/SET , the clock returns to
the set time display.
75+0)"6*'"#.#4/"
To activate Alarm 1 only, slide ALM to ALM 1 ,
then slide ALARM/ON/OFF located on the
back of the clock to ON , or ...
to activate Alarm 2 only, slide ALM to ALM 2 ,
then slide ALARM ON/OFF located on the
back of the clock to ON , or ...
to activate both Alarm 1 and Alarm 2, slide
ALM to ALM 1 + ALM 2 , then slide ALARM ON/
OFF located on the back of the clock to ON .
5KIPCN"+PFKECVQT 5KIPCN"5VTGPIVJ
Blank No signal
Single bar Weak
Double bar Medium
Triple bar Strong
6QYGT"+PFKECVQT +PFKECVGU
Blinking The clock is receiving
Static On Successful reception
Off
No reception/failed
reception
± ± ± ± "016'" ± ± ± ± "
• When the switch is at ALM 1 + ALM 2
position, alarm setting is not available
• Press ALARM/SET at any time to view the
set alarm time according to the alarm switch
position ALM 1 or ALM 2.