Royal Appliance 016 - Manual (Page 13)

DESCALING
93
In this case, the following message will be
displayed:
"DESCALING "
When this message is displayed, the machine
does not stop; however, it is suggested to descale
quickly the machine.
To cancel the message, see programming menu
indications, point 14.
The machine has been adjusted on a 25°òH
value, which causes the warning light to switch
on after 150 l approx.
Should it be necessary, the water hardness value
may be exactly programmed, following the
instructions shown at page 82.
The following adjustments are possible:
Hardness 4: high water hardness, over 29°òH
(14°dH), i.e. 80 l water approx.
Hardness 3:medium water hardness, approx.
20-29°òH (7-14°dH), approx. 150 l water
passage.
Hardness 2:soft water, approx. 12-20°òH
(4-7°dH) approx. 300 l water passage
Hardness 1:very soft water, less than 10°òH
(3°dH), approx. 500 l water passage
In hard water regions, a filter should be used both
to improve the coffee quality or to protect the
machine, thus reducing the descaling frequency.
Note: for this purpose, use a descaling product
suitable for coffee machines.
Never use vinegar!
Descaling can be performed in two ways:
Automatic descaling
Select this mode in the programming menu (see
page 84).
By means of keys
, move the asterisk at
the end of the line on the menu item Descaling
and confirm the selection with the ENT key.
The following message will be displayed:
"13 DESCALING "
DESCALING
94
Pour a discaling solution into the water tank
(according to the instructions on the product
package). Switch the machine on the programming
mode. Place a large container under the steam/
hot water spout and open slowly the steam knob.
The automatic descaling starts: Small amounts of
descaling solution are pumped into the circuit.
Then the pump stops to let the solution take effect.
During this phase, the following message is
displayed:
"MACHINE IS "
"DESCALING "
After approx. 45 minutes, when the procedure is
accomplished, the following message will be
displayed:
"DESCALING "
"FINISHED "
Close the steam knob. The pump stops.
Press ENT button. A display message reminds
you to rinse away any possible descaling residues
from the machine.
"RINSE MACHINE "
Remove water tank, rinse it accurately and fill it
with fresh water. Clean the machine using the
hot water knob and let the whole tank content
flow out. The following message will be displayed:
"RINSING "
"FINISHED "
Press the hot water key again. Go back to
programming function by pressing the ENT key.
Note: By pressing the ESC key, it is possible to
quit descaling procedure.
Reset descaling message
In programming function, by pressing keys
,
move the asterisk till the end of the line on the menu
Sign. Descal and confirm the selection with
ENT button.
The following message will be displayed:
"RESET DESCALING "
"NO "
By means of the same keys , it is possible
to modify the value; Yes or no.
Through this reset operation, the internal counters
of the two water systems are reset and the
message DESCALE is erased.
If the function
"SIGN. DESCAL. "
is selected without the displayed message
Descale, the following message will be
displayed:
"QUANTITY WATER "
"NOT REACHED "
Standard descaling
Switch off the machine. Pour a descaling solution
into the water tank (according to the instructions
on the product package). Place a large container
under the steam/hot water spout (7). Switch the
machine on by pressing the main switch, press
the hot water key and let the descaling solution
in the water tank pour out of the spout for 1 minute
approx.
Press hot water key to complete the operation.
Switch the machine off and let the solution taking
effect for 5 minutes approx. Repeat this procedu-
re two or three times, to empty the water tank.
As soon as descaling has been performed, rinse
the water tank (11) thoroughly and fill it with fresh
water.
Switch on the machine again and let water (2
l approx.) flow out of the steam/hot water
dispensing tube in order to rinse away residues.
Important:
A periodic descaling ensures a correct machine
functioning and avoids expensive repairs. The
machine warranty does not cover damages
occurring as a result of the non-observance of
descaling procedures, improper use and non-
observance of any other instruction contained
herein. Maintain the manufacturer’s adjustment if
the water hardness degree is not known.
Disposal
Machines which are no longer operational
should immediately be made non serviceable,
by cutting the power cord. Machines should be
delivered to a public disposal centre.
Switch off and unplug the machine if it will not be
used for long periods.
Cut the supply power cord and deliver the
machine to a public collecting point.
Should the machine not be used anymore,
switch it off and unplug it.
Keep the machine in a dry place, far from the
reach of children.
Should the machine not be used for a long
period, keep it from dust and dirt
Maintenance
Periodically check the machine working and
clean it in accordance to the instructions.
Troubleshooting
In case of failure, fault or suspected damage
following a fall, unplug the machine immediately.
To fix problems, follow the instructions in the
table. Otherwise contact authorised personnel.
Only skilled personnel are authorised to repair
the machine. The user might incur serious injuries
should repairs not be properly carried out.
The manufacturer declines any liability
whatsoever, should repairs fail to be carried out
according to the instructions contained in this
manual: Furthermore in these cases warranty
rights cannot be honored.