RCA 811-R50391W011 - Manual (Page 2)

compatible ipod types
• iPod nano (1st generation) 1GB, 2GB, 4GB
• iPod nano (2nd generation) 2GB, 4GB, 8GB
• iPod nano 3rd generation (video) 4GB, 8GB
• iPod mini 4GB, 6GB
• iPod 5th generation (video) 30GB, 60GB, 80GB
• iPod classic 80GB, 160GB
• iPod touch 8GB, 16GB,32GB
Installing the ipod Dock adaptor
1. Before connecting your iPod, you need to install the
appropriate iPod Dock Adapter(supplied with the
iPod or sold separately) in the dock of the unit.
2. Insert your iPod Dock Adapter into the dock until it
sits firmly in place.
removing the ipod Dock adaptor
1. Remove the iPod Dock Adapter as illustrated in the
figure to the right.
2. Replace it with another one you need.
Inserting your ipod
1. Ensure the appropriate iPod Docking Adapter is
installed.
2. Insert your iPod into the connector in the dock.
notes:
• Under AC power supply, the iPod will be charged automatically.
• Under battery operation, the iPod will not be charged.
pausing playback
• Press the pLay/paUSe
button.
• To resume playback, press the pLay/paUSe button again.
Skipping to a another track
• Press the button to skip to the beginning of the current track or skip to previous
track. Press the button to skip to the beginning of the next track.
Locating a particular point on a track
• Keep either the or button pressed during playback, according to the desired
direction, and release at the desired point.
note: Please refer to the user's guide that was included with your iPod for more details.
1. Press the StanDBy/on / button to turn on the unit.
2. Press the pLay/paUSe
button to start playing.
note: When you are listening to iPod, please disconnect all other audio devices.
Start playback
to aDJUSt tHe VoLUme
Adjust the VOLUME control to obtain the desired volume.
for perSonaL LIStenInG
Connect headphones ( Ø3.5mm stereo mini plug) to the PHONES jack. Adjust the
VOLUME control to obtain the desired volume.
When headphones are connected, the speakers are automatically disconnected.
1/5. VOLUME +/- buttons
2/4. / buttons
3. STANDBY/ON / button
6. PLAY/PAUSE
button
Using the remote control correctly
• Point the remote control at the REMOTE SENSOR located on the unit.
• When there is a strong ambient light source, the performance of the infrared
REMOTE SENSOR may be degraded, causing unreliable operation.
• The recommended maximum effective distance for remote operation is about 16 feet
(5 meters).
1
2
3
5
4
6
note: If the remote control is not going to be used for a long time, remove the battery
to avoid damage caused by battery leakage corrosion.
WarnInGS:
• Do not dispose of battery in fire; battery may explode or leak.
• Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
• Danger of explosion would be resulted if battery is incorrectly replaced. Replace only
with the same or equivalent type of battery.
caUtIon: When discarding batteries, environmental problems must be considered and
local rules or laws governing the disposal of these batteries must be strictly followed.
attentIon
Remove the protective plastic tab
before operating the remote control.
1. Open the battery door.
2. Insert one CR2025 (3V) size battery.
Battery replacement
When the battery becomes weak, the operating distance of the remote control is greatly
reduced and you will need to replace it.
remote controls
Volume adjustment
Listening to your ipod
The descriptions and characteristics in this
owner’s manual are for the purpose of general
reference only and not as a guarantee.
In order to provide you with the highest
quality product, we may make changes
or modifications without prior notice. The
English version serves as the final reference
on all product and operational details should
any discrepancies arise in other languages.
Troubleshooting tips
System doesn’t turn on
• Unplug the unit for a moment,
and then plug it back in.
• Check the outlet by plugging in
another device.
no sound
• Adjust volume setting.
• Make sure you’ve selected the
correct function.
ipod does not start play
• Make sure the iPod is properly
connected to the universal
dock for iPod.
eSD remark:
In case of misfunc tion due to
electrostatic discharge just reset
t h e p ro d u c t ( d i s co n n e c t a n d
reconnect of the power source may
be required) to resume normal
operation.
Cleaning the exterior
• Disconnect the system from AC
power before cleaning the exterior
of the unit with a soft dust cloth.
• Clean the exterior with a soft clean
cloth or slightly moistened chamois
leather. DO NOT use solvents as it
may cause damage to the unit.
more information
Design and specifications are subject to change without notice.
DC: 12V EXTERNAL DC SUPPLY
BATTERY SUPPLY: 1.5Vx6 “C” SIZE/UM-2/LR14/MN1400
Specifications
connecting to aUX In for other sound sources
You can connect audio devices such as your iPod, CD players or MP3 players to the unit
through the AUX IN jack. Use the Line-in cable (not supplied), connect the AUX IN jack
on the back panel to the Line Out or Earphone jack of the other audio devices.
Listening to the connected Device
Turn on the audio device you have attached to the AUX IN jack.
aUX In connection
Printed in China
811-R50391W011
to change Battery