RCA RS27116I - Manual (Page 2)

Installing an iPod Dock Adapter
1. Before connecting your iPod, it’s
recommended that you install the
appropriate iPod Dock Adapter (supplied
with the iPod or sold separately) in the dock
of the unit.
2. Insert your iPod Dock Adapter into the dock
until it sits firmly in place.
Removing the iPod Dock Adapter
1. Remove the iPod Dock Adapter as illustrated
in the figure to the right.
2. Replace it with another one you need.
Inserting Your iPod
1. Insert your iPod into the connector in the
dock.
2. Press the STANDBY/ON button to turn on
the unit.
3. Press the FUNCTION button repeatedly
until the indicator “iPod” appears on the
display.
4. Press the PLAY/PAUSE button to start
playing.
Notes:
• The iPod will charge automatically (until
fully charged) once it is docked in the cradle.
• To prevent interference to AM radio signals, please switch off the iPod
while listening to AM stations.
Pausing Playback
• Press the PLAY/PAUSE button.
• To resume playback, press the PLAY/PAUSE button again.
Skipping to a Another Track
• Press either the or button according to the desired direction.
• Press the button to skip to the beginning of the current track or
previous track. Press the button to skip to the beginning of the
next track.
Locating a Particular Point on a Track
• Keep either the or button pressed during playback, according
to the desired direction, and release at the desired point.
Repeat Playback
Repeat lets you play songs repeatedly (a single repeat or all songs
repeat).
Compatible iPod Types
• iPod nano (1st generation) 1GB, 2GB, 4GB
• iPod nano (2nd generation) 2GB, 4GB, 8GB
• iPod nano 3rd generation (video) 4GB, 8GB
• iPod nano 4rd generation (video) 8GB, 16GB
• iPod 5th generation (video) 30GB, 60GB, 80GB
• iPod classic 80GB, 120GB, 160GB
• iPod touch (1st generation) 8GB, 16GB, 32GB
• iPod touch (2nd generation) 8GB, 16GB, 32GB
Note: Also supports iPhone when iPhone is set to “airplane mode”.
Listening to Your iPod
Preset EQ
Timer Setting
Sleep Timer Setting
Display Function
Troubleshooting Guide
Limited Warranty Limited Warranty
Maintenance
1. Press the STANDBY/ON button to turn on the unit.
2. Slide the OPEN knob to open the CD door. Place a disc in the center
with the label side front and then close the CD door gently.
3. Press the FUNCTION button to CD mode. “- -” will blink on the
display. Then the total track no. is shown on the display.
4. Press the PLAY/PAUSE button to start playing.
• Adjust the volume levels.
To Pause Playback
• Press the PLAY/PAUSE button.
• To resume playback, press the PLAY/PAUSE button again.
To Stop Playback
• Press the BAND/ STOP button.
Skipping to Another Track
• Press either the or button according to the desired direction.
Press the button to skip to the start of the current track or skip
to previous tracks. Press the button to skip to the beginning of
the next track.
Locating a Particular Point on a Track
• Keep either the or button pressed during playback,
according to the desired direction, and release at the desired point.
REPEAT PLAYBACK
Repeat Current Track
• Press the MEM.UP/ button until “ REPEAT ” blinks on the display. The
current track will be played repeatedly.
Repeat the Entire CD
• Press the MEM.UP/ button until “ REPEAT ” stops blinking and remains
on. All tracks will be played repeatedly.
Cancel Playback Mode
• Press the MEM.UP/ button until repeat indicator disappears.
RANDOM PLAYBACK
All tracks on the disc can be played in random order (Using the remote
control only).
Random Playback
• Press the RANDOM button on the remote
control and “RANDOM” will be shown on the
display. All tracks will be played randomly.
After all tracks have played, the unit will stop
automatically.
Cancel Random Playback
• Press the RANDOM button on the remote control again during
RANDOM playback to return to normal playback.
PROGRAMMABLE CD PLAYBACK
A program of up to 20 tracks can be set to play in a preset order.
1. In CD stop mode, press the PROG/MEM/
( ) button and “MEMORY” & “- -” will blink on
the display.
2. Press the or button to select the desired
track then press the PROG/MEM/ ( ) button
to store the track in memory.
3. To add additional tracks, repeat step 2 (up to 20 tracks).
4. To start playback, press the PLAY/PAUSE button.
To Check the Program:
• Press the BAND/ STOP button and the or button. Each time
the button is pressed, the track number appears on the display.
To Change the Programmed Tracks during Program
Playback:
• Press the BAND/ STOP button and press the PROG/MEM/ ( )
button repeatedly to search the program number, then press either
the or button to select the desired track. Press the PROG/
MEM/ ( ) button again to register the newly selected track into
program.
To Erase the Whole Program, Do One of the Following:
• Press the FUNCTION button to change to radio/iPod/AUX mode.
• Press the STANDBY/ON button to turn off the unit.
• Press BAND/ STOP button repeatedly until “MEMORY” disappears.
CD Playback CD Playback
RANDOM
MEMORY
iPod Dock Adapter
Listening to Your iPod
Listening to Your iPod
This system supports a variety of equalizers and sound effects.
During playback, press the PRESET EQ button to select a desired music
mode. Each time the PRESET EQ button is pressed, the music mode will
be changed to the next one as follows:
-> (ROCK) -> -> (CLASSIC)
The timer function will turn the unit on at a preset time.
To Set Timer
1. In standby mode, press and hold the TIMER button on the remote
control until the TIMER indicator blinks.
2. Press and hold the PROG/MEM/ ( ) button until the hour digits blink.
3. Press the or button to adjust the desired hours then press
the PROG/MEM/ ( ) button once to confirm. The minute digits
will begin to blink.
4. Press the or button to adjust the desired minutes then press
the PROG/MEM/ ( ) button once to confirm. The TIMER indicator
will stop blinking and remain on.
5. The unit will wake up to “RADIO”, “ iPod” ,“AUX IN” or “CD” when the
timer reaches the preset time.
• For RADIO timer, first tune in to a desired station.
Press the STANDBY/ON button to enter standby mode, then set
the timer following the above steps.
• For CD timer, first press the FUNCTION button to CD mode and insert
one CD into the unit.
Press the STANDBY/ON button to enter standby mode, then set
the timer.
• For AUX IN timer, first connect the plug to the AUX IN jack in back panel. Press
the STANDBY/ON button to enter standby mode, then set the timer.
• For iPod timer, first insert your iPod into the connector, Press the
FUNCTION button to iPod mode. Press the STANDBY/ON button
to enter standby mode, then set the timer.
Note: Before setting timer, you can adjust the volume levels in RADIO/
CD/iPod/AUX IN mode for the timer.
To Cancel Timer
• Press and hold the TIMER button on the remote control until the
TIMER indicator goes out.
CD Mode
1. During playback, press the DISPLAY button repeatedly to shuffle
between the CD playback mode and the current time.
2. When stopped, press the DISPLAY button to shuffle between the total
number of CD tracks and the current time.
Radio/iPod/AUX Mode
• Press the DISPLAY button to shuffle between the current playback
mode and the current time.
The sleep timer automatically turns the unit off after a certain time.
1. While the unit is on, press the SLEEP button and “ ” appears on
the display.
2. Press the SLEEP button repeatedly to select the desired sleep time
as below:
3. The unit will automatically turn off once it counts down the sleep time.
• To clear the preset sleep time press the SLEEP button until “ 00 ”
appears.
Cleaning the Unit
Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth .
Cleaning the CD
If the CD skips or will not play, the disc may need to be cleaned.
Before playing, wipe the disc from the center outwards with a cleaning cloth.
After playing, store the disc in its case.
Handling the Disc
Only touch the CD on the edge to avoid finger prints on its surface.
Do not stick paper or tape nor write anything on the surface.
PRoblems solutions
CD
System does not
turn on
• Make sure AC adapter is secure in the outlet, and outlet
has power.
• Make sure you’ve selected CD mode.
Disc in place but
unit won’t play
• Make sure disc label is facing front.
• Make sure disc is clean.
• Pause mode is activated.
• Disc may be damaged or dirty; check disc.
Disc skips • Make sure the unit is on a secure spot. Vibration or
jarring can cause the disc to skip.
RADIO
Poor FM reception • Make sure FM antenna wire is fully extended.
• Electrical interference in your home can cause
poor reception. Move the unit away from them
(especially those with motors and transformers).
Poor AM reception • Rotate the unit horizontally.
iPod
iPod does not dock
properly or does not
install properly.
• Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on
your iPod.
iPod does not
respond to the
speaker system.
• Make sure that your iPod is working properly before
docking into the unit. Please refer to your iPod
manual for details.
AVC MULTIMEDIA ("AVC") makes the following limited warranty. These
limited warranties extend to the original consumer purchaser and is limited
to non-commercial user of the product.
One Year Parts & Labor Warranty
AVC products purchased in the United States are warranted to be free from
defects in materials or workmanship for a period of one year from the date
of their original retail purchase. If the unit fails to conform to this warranty,
we will service the product using new or refurbished parts and products, at
AVC's sole discretion.
During a period of one year from the effective warranty date, AVC will
provide, when needed, service labor to repair a manufacturing defect at
its designated Service Center. To obtain warranty service in the United
States, you must first call our Customer Support Center at 1-800-506-
5746 or 1-877-252-6873, during the hours listed in the box below. The
deternination of service will be made by AVC customer support.
PLEASE DO NOT RETURN YOUR UNIT TO AVC WITHOUT PRIOR
AUTHORIZATION. New or remanufactured replacements for defective parts
or products will be used for repairs by AVC at its designated Service Center
for one year from the defective warranty date. Such replacement parts or
products are warranted for an additional one year from the date of repair or
replacement. The Customer will be required to ship the unit to the Service
Center indicated at the time Customer Support is contacted to make the
necessary repairs. The customer is responsible for all transportation charges
to the service facility.
Packaging and Shipping Instruction
When you send the product to the AVC service facility you must use the original
carton box and packing material or an equivalent as designated by AVC.
Your Responsibility
(1) You must retain your bill of sale to provide proof of purchase.
(2) These warranties are effective only if the product is purchased and
operated in the U.S.A. or Canada.
(3) Warranties extend only to defects in material or workmanship, and do
not extend to any product or parts which have been lost or discarded,
or damage to product or parts caused by misuse, accident, improper
operation or maintenance, or use in violation of instructions provided
with the product, or to product which has been altered or modified
without authorization of AVC, or to products or parts thereof which
have had the serial number removed or changed.
Out of Warranty
In the event your product requires repair after the limited warranty period has
expired, please contact our Customer Support Center at 1-800-506-5746,
1-877-252-6873 or
www.RCAav.com
Hours: Monday-Thursday: 9am-7pm, Friday: 9am-5pm, Saturday: 9am-NOON
Eastern time.
Important:
You are responsible for any transportation, shipping or insurance relative to the
return of the product to our Product Returns Center.
All warranties implied by state law, including the implied warranties of
merchantability and fitness for a particular purpose, are expressly limited to
the duration of the limited warranties set forth above. With the exception
of any warranties implied by state law as hereby limited, the foregoing
warranty is exclusive and in lieu of all other warranties, guarantees,
agreements and similar obligations of manufacturer or seller with respect
to the repair or replacement of any parts. In no event shall AVC be liable for
consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change,
modify or extend the terms of these warranties in any manner whatsoever.
The time within action must be commenced to enforce any obligation of
AVC arising under the warranty or under any statute, or law of the United
States or any state thereof, is hereby limited to one year from the date of
purchase. This limitation does not apply to implied warranties arising under
state law.
This warranty gives you specific legal rights and you may also have other
rights, which may vary from state to state. Some states do not allow
limitation on how long an implied warranty lasts, when an action may
be brought, or the exclusion or limitation of incidental or consequential
damages, so the above provisions may not apply to you.
For more information on other products and services, please contact our
web site at www.RCAav.com
Important: Also keep your “Bill of Sale” as proof of purchase.
Model no ..................................................... Product name .................................................
Type of set ..................................................................................................................................
Serial no. ...................................................... Invoice no. .......................................................
Date purchased ......................................... Dealer name ...................................................
FOR SUPPORT, SERVICE AND REPAIR, PLEASE VISIT www.RCAav.com
Specifications and external appearance are subject to change without
notice.
• Press the MEM.UP/ button on the remote control. The repeat
indicator appears on the iPod screen.
• To cancel repeat playback, press the MEM.UP/ button until the
repeat indicator disappears.
Note: Please refer to the owner’s manual that was included with your
iPod for more details.
Random Playback
Random plays songs/albums from your iPod in a random order.
1. Press the RANDOM button on the remote control once and the
random indicator appears on the iPod screen. All songs will be
played without sequence.
2. Press the RANDOM button on the remote control twice and the
random indicator appears on the iPod screen. All songs of this
albums will be played without sequence.
• To cancel shuffle playback, press the RANDOM button until the
shuffle indicator disappears.
Note: Please refer to the owner’s manual that was included with your
iPod for more details.
AUX IN Connection
Connecting to AUX IN for Other Sound Sources
You can connect audio devices such as your iPod, CD players, MP3 Players,
or PC to the unit via the AUX IN jack. To do this, connect an audio cable
with 3.5mm plugs from the line out or headphone out jack of the other
audio device to the AUX IN jack on the unit’s back panel.
Listening to the Connected Device
1. Press the FUNCTION button to AUX IN mode and “AU” is shown on
the display.
2. Turn on the audio device you’ve attached to the AUX IN jack.
- 8 - - 9 - - 11 - - 10 -
- 12 - - 13 - - 14 -
Printed in China 811-711691W062
Need More Help?
Please visit online help at http://www.RCAav.com
811-711691W062 ENG RCA.indd 2 2009-05-22 15:05:35