Rangemaster KITCHENER U109720 - 01 - Manual (Page 29)

29
WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
18. To Change Tall Oven Door Magnetic Latch
Remove the control panel (see 1).
Remove the plinth (3 screws) and the central vertical
cover (5 screws). Prize the retaining clip off the magnet
unit. Fit new unit and retaining clip.
Reassemble in reverse order.
Check correct door operation.
19. To Remove Grill Element.
Disconnect from electricity supply.
Remove grill pan from grill chamber. From inside grill
compartment remove enamelled front shield from
grill roof, 2 screws and washers. Remove 2 screws
and washers securing the grill element front support.
Remove the screws from the grill elements.
Lift elements out carefully, disconnect the leads from
the element terminals noting their position. If it is not
possible to disconnect the leads in this way, pull cooker
forward to gain access to the rear, remove screws
securing the electric cover to the back sheet and remove
cover and disconnect the terminals from the rear.
Fit new elements, reassemble in reverse order. Check
operation of grill.
18. To Remove an Oven Inner Back.
Open the oven door and remove the screws and washers
securing the inner back to the back of the oven.
Carefully lift away the inner back. Reassemble in reverse
order making sure that the 4 screws and washers are
fully tightened.
19. To Change Fan in Oven.
Disconnect from electricity supply.
Pull cooker forward to gain access to the rear. Remove
screws securing the electric cover to the back sheet and
remove cover. Disconnect the 3 terminals connected to
the fan noting their position. Remove oven inner back
(see 18). Hold the fan blade and remove the centre nut
(left hand thread) 2 brass washers, fan blade and Circlip.
Unscrew fan retaining nuts and washers (3 off each) and
lift the fan away from the rear of the cooker. Fit new fan
and reassemble in reverse order. Check operation of
oven.
20 To Remove an Oven element Thermal Cut-Out.
Disconnect from the electricity supply.
Pull the cooker forward to gain access to the cover
box. Undo the cover screws and lift clear. The cutout
is located on the earth plate beside the oven element
connections. Disconnect the cutout wiring. Undo the
fixings that secure the cutout to the earth plate and
remove. Fit replacement control and re-assemble in
reverse order.
Carefully lift off the outer door panel.
Remove door handle from panel by unscrewing 2
retaining nuts. Fit door handle to new panel
Fit panel to door. Reassemble in reverse order.
14. To Change the Main Oven Door Latch
Remove outer door panel (see 13).
Remove screws ‘B’ holding latch
assembly to inner door panel.
Fit new catch and reassemble in
reverse order.
Check correct door operation.
15. To Adjust the Main Oven Door Catch Keep
Open oven door, slacken off
locknut at base of keep, and
screw in or out as required until
required fit is obtained.
Retighten locking nut.
16. To Change Oven Door Seal
Open oven door. The seal is held in place by small hooks
on the rear face. At the corner pull seal diagonally away
from the door centre until that hook is released. Proceed
to the next hook and release it in a similar way, and so
on. Use force if the hooks are stiff, as the old seal will be
discarded.
When fitting new seal, position the seal join at the
bottom. Hook the new seal in one of the corner holes of
the door, and proceed round the door snapping in each
hook in turn.
17. To Change Tall Oven Door Outer Panel
Remove oven door see 12. Lay door face down on a
suitable surface and remove 2 screws from bottom edge
of door and 2 screws from inside face of door.
Remove outer door panel. Remove door handle by
unscrewing 2 screws. Remove 2 cross-headed screws
holding door handle fixing bracket to door panel. Fit
door handle bracket and door handle to new panel.
Fit panel to door. Reassemble in reverse order.