Rheem ASME 40 - Manual (Page 4)

Water heater(s) shall be model ________________, manufactured by RHEEM-RUUD, having electrical input of __________
kW and a recovery rate of _____________ GPH at a 100°F temperature rise. Water heater(s) shall have a storage capacity of
___________ gallons. Water heater(s) shall have the UL seal of certification and be factory equipped with an AGA/ASME rated
temperature and pressure relief valve. Water heater(s) shall be constructed in accordance with the requirements of the ASME
Boiler and Pressure Vessel Code, Section IV Part HLW. Tank(s) shall have a coating of high temperature porcelain enamel and
furnished with two (2) magnesium anode rods rigidly supported. Water heater(s) shall meet or exceed the standby loss require-
ments of ASHRAE Standard 90.1b-2001. Tank(s) shall have a working pressure of 160 psi, and shall be completely assem-
bled. Water heater(s) shall be approved-listed and constructed in accordance with UL Sanitation (NSF5). Water heater(s) shall
be equipped with LIFEGUARD “screw-in” type elements featuring a stainless steel outer sheath of INCO-LOY 840 material.
Tank shall be insulated with 2-1/2" of rigid polyurethane foam insulation. Water heater(s) shall be constructed with a SYSTEM
SENTINEL element diagnostic panel utilizing light emitting diodes. Each LED will correspond to the number and location of the
heating elements and monitor their on-off function. Water heater(s) shall be provided with internal power circuit fusing, control
circuit fusing, magnetic contactors, 120 volt control circuit transformer and immersion thermostat(s) with manual reset high limit
control. 3/4" inlet and outlet water connections shall be provided. Water heater(s) shall be covered by a three year limited
warranty against tank leaks.
This product features a three year limited warranty against tank leaks.
Please refer to Commercial Warranty Information brochure for complete warranty information.
Recommended Specifications:
Limited Warranty:
C O M M E R C I A L
W A T E R H E A T E R S
Rheem Water Heating • 101 Bell Road, Montgomery, Alabama 36117-4305 • www.rheem.com
Rheem Canada Ltd./Ltée,128 Barton Street West, Hamilton, Ontario L8N 3P3
P R I N T E D I N U . S . A 0 2 / 0 6 W P F O R M N O . R R 1 0 2 C E - 5 R e v. 5
In keeping with its policy of continuous progress and product improvement, Rheem-Ruud reserves the right to make changes without notice.
PowerPack continued.
Other Features:
• Integral Fusing
all models have integral fusing for each element.
• Anode Rods
two (2) magnesium anodes are installed in each tank
to ensure long life and corrosion resistance.
• Temperature and Pressure Relief Valve
AGA/ASME rated and factory installed.
• Electrical Connections
pre-wired, accessible control box with multiple
knock-outs on side in size selections to match the
National Electric Code. Sizes range from 1/2" to 2".
A grounding screw is provided for attaching an
equipment grounding conductor.
• Single Panel Control Box
with hinged door, provides immediate access to all
electrical components and elements.
• Terminal Block
all models are equipped with U.L. listed terminal
blocks for simplicity of installation. The terminal
block will accept either copper or aluminum field
connect wire.
• 120 Volt Control Circuit
all units are furnished with a fused 120 volt control
circuit. This circuit is created by an internal multi-tap
transformer of unique design that has four (4) taps
for the primary voltages, 208, 240, 277 and 480.
• Water Connections
hot outlet and cold inlet are 3/4" NPT plastic lined
nipples which prevent excessive turbulence of
heated water and results in optimum tank draw.