Onkyo TX-NR808 - Manual (Page 27)

27
En
Note
*1 If Pure Audio or Direct listening mode is selected,
“Dynamic EQ” and “Dynamic Volume” cannot be selected.
*2 Only when you have selected “Custom” in the “Picture
Mode” (
➔ 53), pressing ENTER allows you to adjust the fol-
lowing items via the Home menu; “Brightness”, “Contrast”,
“Hue” and “Saturation”. Press RETURN to return to the
original Home menu.
*3 Depending on the input source and listening mode, not all
channels shown here output the sound.
*4 When you have entered a custom name in “Name Edit”
(
➔ 52), the input source is displayed with that name. But
even if not, the component name may be displayed if the AV
receiver receives it via HDMI connection (
➔ 18).
*5 For the PORT input selector, the name of Universal Port
Option Dock will be displayed.
When you connect an -capable Onkyo component, you
must configure the input display so that can work
properly.
This setting can be done only from the front panel.
Note
• DOCK can be selected for the TV/CD, GAME or VCR/DVR
input selector, but not at the same time.
• Enter the appropriate remote control code before using the
remote controller for the first time ( ➔ 80).
Note
• Always turn down the volume before connecting your head-
phones.
• While the headphones plug is inserted in the PHONES jack, the
Headphone indicator, speaker/channel indicator FL and FR
lights. (The Powered Zone 2 speakers are not turned off.)
• When you connect a pair of headphones, the listening mode is
set to Stereo, unless it’s already set to Stereo, Mono, Direct, or
Pure Audio.
• Only the Stereo, Direct, Pure Audio, and Mono listening modes
can be used with headphones.
Using the Easy macro command in the Easy macro mode,
you can sequentially operate Onkyo components with sim-
ple commands by simply pressing one button. These com-
mands are user-specifiable (
➔ 85) and the default actions
are described below. Press ACTIVITIES to start the Easy
macro command.
Once the AV receiver has entered the normal macro mode,
all of ACTIVITIES will automatically switch to the nor-
mal macro mode. In this case, pressing ALL OFF will set
only the AV receiver to Standby mode.
Changing the Input Display
1
Press TV/CD, GAME or VCR/DVR so that “TV/
CD”, “GAME” or “VCR/DVR” appears on the
display.
2
Press and hold down TV/CD, GAME or VCR/DVR
(about 3 seconds) to change the input display.
Repeat this step to select “MD”, “CDR”, “DOCK”
or “TAPE”.
For the TV/CD input selector, the input display
changes in this order:
For the GAME input selector, the setting changes in
this order:
For the VCR/DVR input selector, the setting
changes in this order:
TV/CD
→
MD
→
CDR
DOCK
→
→
TAPE
→
GAME
↔ DOCK
VCR/DVR
↔ DOCK
Using Headphones
Connect a pair of stereo headphones with a stan-
dard plug (1/4 inch or 6.3 mm) to the
PHONES
jack.
Using Easy Macros
Press MY MOVIE, MY TV, or MY MUSIC.
MY MOVIE (default):
1. The TV connected to the AV receiver is turned
on.
2. The Onkyo DVD player connected to the AV
receiver is turned on.
3. The AV receiver is turned on.
4. The input selector of the AV receiver is set to
“BD/DVD”.
5. The player starts playback. *1
MY TV (default):
1. The TV connected to the AV receiver is turned
on.
2. The cable set-top box connected to the AV
receiver is turned on.
3. The AV receiver is turned on.
4. The input selector of the AV receiver is set to
“CBL/SAT”. You can enjoy cable TV.