Orion 52080 - Manual (Page 14)

26 27
For the Permanent Stretch Type, the Linear Only mode is useful for adjusting
the range of pixels to match a particular file format. The Log mode is useful
for compressing the dynamic range of the image, but can be rather harsh. The
Gamma mode allows you to selectively emphasize bright or dim parts of the
image by entering a suitable Gamma Value. A Gamma of 1 has no effect, less
than 1 will emphasize faint details, while a value greater than 1 will emphasize
bright details.
The Input Range can be set to Screen Stretch, which in Linear Mode pro-
duces an output matching the current screen appearance. This is useful in
producing final images for output to 8-bit image formats which have limited
range. Note that the minimum and maximum values are always taken from the
screen stretch settings for the original image. These can be adjusted dynami-
cally using, for example, Quick Stretch. The Max Pixel selection sets the input
range from 0 to the brightest pixel in the image. This prevents any image pix-
els from being saturated in the final result, but may produce images with low
contrast. You can also manually set values with Manual Settings in a similar
fashion to the Screen Stretch Window.
The Output Range is used when preparing a file to be saved in a format that
has limited range. The Output Range maps minimum input to zero, and maxi-
mum input to 255, 4095, or 65535 depending on the settings. Any values that
exceed the limits are clipped. The Unlimited setting disables all limiting and is
recommended when performing Gamma and Log stretches; it is appropriate
when the image will be saved in floating point format.
Recommended Processing Sequence
What is the best order to apply the processing functions in? Here is a recom-
mended sequence:
1. Dark Subtract
2. Convert Raw to Color
3. Make Pixels Square
4. Combine
5. Filter
6. Color Balance
7. Stretch
For convenience, you can Make Pixels Square after the combine, unless align-
ment requires rotating the images (i.e. Manual 2 stars is used as the Align
Mode in the Combine Images window). If you need to rotate the images by
more than a small amount, then you should make them square first to avoid
geometric distortion between the frames.
Once you have the combined image, there is a lot more room for experimenta-
tion and tinkering. Be sure to Save a copy of the combined image; otherwise
you might have to go back to the beginning and stack individual images
again!
Note on File Format
When saving images (using Save or Save As in the File menu), you have a
choice of file formats. The default produces .fit files, but .tif, .jpg, .png, and
.bmp file formats can also be selected. Having a choice of output file formats
is useful, especially if images will be exported to other software programs for
additional image processing (like Adobe Photoshop, for instance).
If you save to a file format other than .fit, you will need to check the Auto
Stretch box, or otherwise Stretch the image to change the Output Range (in
the Stretch command window) to match the Size Format (in the Save As win-
dow). Otherwise, the Output Range will likely exceed the Size Format, and the
saved image will be ruined (will turn all white).
For example, say the Output Range is set to create image brightness values in
16-bit format, while the Size Format of a specific file format (.jpg, for example)
may only support 8-bits. Since the 16-bit format sees 65535 brightness levels,
and the 8-bit format can only support 255 levels, all of the levels above 255
in the 16-bit image (i.e. the vast majority of the 16-bit brightness levels) will
be saved at the maximum 8-bit value of 255. So the saved .jpg will have very
little brightness information from levels 1 to 254 and almost all the brightness
information at level 255. Thus a white image results.
If you plan to do all image processing within MaxIm DL Essentials Edition
(or the optional full version of MaxIm DL), saving images in the FITS (.fit) File
Format using the IEEE Float Size Format is recommended. This ensures that
Figure 16. The Stretch command modifies the data contained
within the image in order to improve contrast and brightness.