Omega Lift 13200 - Manual (Page 2)

2
Save these instructions. For your safety, read, understand,
and follow the information provided with and on this jack
before using. The owner and/or operator of this equipment
shall have an understanding of this jack and safe operating
procedures before attempting to use. The owner and/or
operator shall be aware that the use and repair of this product
may require special skills and knowledge. Instructions and
safety information shall be conveyed in the operator's native
language before use of this jack is authorized. If any doubt
exists as to the safe and proper use of this jack, remove from
service immediately.
Inspect before each use. Do not use if broken, bent, cracked,
or damaged parts (including labels) are noted. Any jack that
appears damaged in any way, operates abnormally or is
missing parts, shall be removed from service immediately. If
you suspect that the jack was subjected to a shock load (a
load dropped suddenly, unexpectedly upon it), immediately
discontinue use until the jack has been checked by a factory
authorized service center (contact distributor or manufacturer
for list of Authorized Service Centers). It is recommended that
an annual inspection be done by qualified personnel. Labels
and owner's manuals are available from manufacturer.
PRODUCT DESCRIPTION
This product is designed to lift, position, or move, but not
sustain, rated capacity loads. It is not designed to be used as
a stand-alone device. Any load lifted, positioned, or otherwise
moved by this device, must immediately be supported by
appropriately rated mechanical means. A wide variety of
applications exist for this category of product. Special skill,
knowledge and training may be required for a specific task and
this product may not be suitable for all jobs listed. Unsuitable
applications include applications that call for a device to
lift, position, move or support persons, animals, hazardous
materials, mobile homes and dwellings in general, mirrors,
plate glass or to connect/secure hatches, components, and
materials between bulkheads. The user ultimately must make
the decision regarding suitability of the product for any given
task and therefore accept responsibility for that decision.
HYDRAULIC JACK TECHNICAL
SPECIFICATIONS
Rated Capacity of J13060: 6,000 lbs. (3 ton)
Rated Capacity of J13120: 12,000 lbs. (6 ton)
Rated Capacity of J13200: 20,000 lbs. (10 ton)
Brand name: Omega
Hydraulic Pressure @ Rated Capacity:
J13060: 4,185 psi
J13120: 4,000 psi
J13200: 5,400 psi
BEFORE USE
Before using this jack, ensure that the intended load
contact point is able to withstand the load applied by
this jack.
1. Before using this product, read the owner’s manual
completely and familiarize yourself thoroughly with the
product, its components, and recognize the hazards
associated with its use.
2. To familiarize yourself with basic operation, use the
operating handle to engage and turn the release valve:
a. Clockwise until firm resistance is felt to further thread
engagement. This is the ‘CLOSED’ release valve
position used to pressurize the hydraulic fluid and
raise the ram plunger.
b. Counter-clockwise, but no more than 1 turn from the
closed position. This is the ‘OPEN’ release valve
position used to lower the ram plunger.
3. Check that the pump operates smoothly before putting into
service. Replace damaged or missing parts with factory
authorized replacement parts only. Repair of this product
may require special skills and knowledge and should
only be attempted by a factory authorized service center.
Contact the manufacturer or distributor of this product for
a list of factory authorized service centers. Lubricate as
instructed in Maintenance Section.
Bleeding/ Venting Trapped Air
With the release valve in the OPEN position (2b above) and
with saddle fully lowered, locate and remove the oil filler plug/
screw. Insert the handle into the handle sleeve; then pump
6 to 8 full strokes. This will help release any pressurized air
which may be trapped within the reservoir. Oil level should
be even with the bottom of the oil filler hole. Reinstall the oil
filler plug/screw.
To avoid personal injury and/or property damage:
• Read, understand and follow all printed materials provided
with and on this jack.
• This is a lifting device only! Never work on, under, or
around a load supported only by a hydraulic jack.
• Immediately support the lifted load with appropriately
rated mechanical means.
• Use only on hard, level surfaces capable of sustaining
rated capacity loads.
• Center load on saddle.
• No alteration shall be made to this device. Use only
attachments, adapters and accessories provided by the
manufacturer.
• Be alert and sober when using this product! Never
operate this equipment when under the influence of drugs
or alcohol.
• Use only high grade hydraulic jack oil in this product.
• Always use a calibrated means of determining how
much force is being applied by this product. Never
exceed the rated capacity of the jack.
WARNING !
!
Use of this device may require special skills and
knowledge. Read, understand, and follow all printed
materials provided with and on this device before use.
!
Use of this device may require special skills and
knowledge. Read, understand, and follow all printed
materials provided with and on this device before use.
!