Sylvania SRCD302 - Manual (Page 3)

POWER SUPPLY AND CONNECTION
AC OPERATION
Connect the AC power plug to wall outlet with AC 120V/60Hz.
BATTERY OPERATION
Remove the battery cover and insert batteries 8 x Um2 or C size .Note: Unit
cannot be operated on batteries with AC power connected. Observe the polarity (+)(-)
markings in battery compartment.
LISTENING TO RADIO BROADCAST
OPERATION
Set the function switch to RADIO position on unit
Slide the BAND switch to desired band
Pull out
extend the rod antenna for FM, station.
Rotate the tuning knob to receive the desired broadcast.
CD OPERATION INSTRUCTION
PLAYING CD-COMPACT DISC
1. Slide the Function Switch to the CD position, the lndicator will light and the Display will
show a dash.
2. Press
of the disc compartment cover and lift up the cover. OPEN
3. Place a disc with label side up on the centre hub. Make sure to place a disc flat in the
compartment.
4. Close the disc compartment cover, display will show the total number of tracks (songs)
on the CD.
5. To start the music, press the CD Play/Pause Button (wait a few seconds for music to
start). The first track number “1” will appear in the Display, the Play/Program lndicator
will light and the disc will start playing.
6. Adjust the Volume Control to your taste.
7. To pause the music, press the Play/Pause Button, the track number will flash to remind
you that you are in pause mode.
8. To resume the music from pause, press the Play/Pause Button again. The track number
will stop flashing.
9. To stop playing music. press the CD Stop Button.
10.To turn off the CD, slide the Function Switch to
position. The Power Indicator will OFF
go off.
SKIPPING TRACKS (SKIP)
1. This function enables you to find any desired track during playing. If the CD Forward
search/Skip( )Button is pressed once or repeatedly the NEXT TRACK or one of the
following tracks will be selected. The Display will show the track or song number.
2. If the CD Back Search/Skip( )Button is pressed, play will go BACK one track per press.
3. When the set is in the pause mode, it is also possible to select the beginning of a certain
track by using the CD Forward Search/Skip ( )Button and CD Back Search/Skip ( )
Button to reach the desired track. After selection, press Play.
4. Press and HOLD the CD Forward Search/Skip ( )Button to search forward at a high
speed for a particular point of a song. Press and HOLD the CD Back Search/Skip ( )
Button to search backward. Release the button to resume normal play when the point is
found.
Important Safety Instructions
13) Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
14) Protective Attachment Plug – The product is equipped with an attachment plug having overload protection. This
is a safety feature. See Instruction Manual for replacement or resetting of protective device. If replacement of the
plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has
the same overload protection as the original plug.
15) Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the
antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,ANSI/NFPA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements
for the grounding electrode.
NEC-NATIONAL ELECTRICAL CODE
16) Lightning – For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will
prevent damage to the product due to lightning and power-line surges.
17) Power Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with
them might be fatal.
18) Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
19) Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind
on the product.
20) Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
21) Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance – this indicates a need for service.
22) Replacement Parts – When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
23) Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks to determine that the product is in proper operating condition.
24) Wall or Ceiling Mounting – The product should be mounted to a wall or ceiling only as recommended by the
manufacturer.
25) Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
2 3