Omnitron Systems Technology iConverter 2GXM - Manual

iConverter 2GXM Standalone Module QUICK START GUIDE
The Omnitron iConverter ® 2GXM media
converter and Network Interface Device (NID)
with integrated management provides Gigabit
Ethernet (1000BASE-X) fiber-to-fiber media
conversion.
The 2GXM conforms to Ethernet in the First
Mile (EFM) fiber standards to support Fiber-
to-the-X (FTTX) Metropolitan and Enterprise
LAN networks. Built-in Operation,
Administration and Maintenance (OAM)
functionality enables the 2GXM to operate as
a managed demarcation point at the customer premises and network edge, offering
Quality of Service capability.
The 2GXM can be managed using Omnitron’s NetOutlook TM SNMP Management
Software, 3rd Party SNMP Client, Telnet or the Command Line Interface (CLI).
For more information, including the complete User Manual on the 2GXM module, access
Omnitron’s documentation download web page to view all relevant documents:
http://www.omnitron-systems.com/downloads.php
INSTALLATION PROCEDURE
1) Configure DIP-Switches
2) Install Standalone Module and Connect Cables
3) Configure Module via Command Line Interface
4) Verify Operation
1) CONFIGURE DIP-SWITCHES
DIP-SWITCH BANK 1
SW1, SW2 - AUTO/MANUAL NEGOTIATION “AN/MAN”
When the DIP-switch is in the DOWN Auto-Negotiate “AN” position (factory default),
t h e P o r t a u t o m a t i c a l l y
determine the duplex and
pa u s e m o d e s o f t h e
c o n n e c t i n g f i b e r o p t i c
devices. If the connecting
fiber optic devices cannot
provide the proper signal to
indicate their own mode of
operation, the DIP-switch
should be set to the UP
Manual “MAN” position.
See Figure B on page 2 for more information.
NOTE: When Port 1 operates in Auto-Negotiation mode, the port advertises for
Pause. When the Fiber optic ports (Port 1 and Port 2) operates in Manual mode,
Pause is disabled.
Management Options iConverter, Serial Agent
Network Management
1: Chassis and Module Management
2: Set Module Name Preferences
Management Module Preferences
3: IP and Control Preferences
4: SNMP Preferences
5: Abandon Preference Changes
6: Save Preference Changes
7: Restore Factory Defaults
8: Restart Management Module
9: Other Networking Features
Management Module Maintenance
10: Firmware Update
11: Set Date/Time
IP Address = 192.168.1.220
Chassis Number = 1
Enter Choice, <H>elp, E<x>it >
Figure C: Command Line Interface Menu Options
The CLI interface allows for the detailed configuration of the module. It is recommended
to configure the module with an IP address associated with the attached network.
Also, SNMP traphost address should be configured if the module is managed with an
SNMP-based Management System. See the 2GXM User Manual for complete
information.
4) VERIFY OPERATION
Once the module has been installed and configured per steps 1 - 3, verify the module
is operational by viewing the LED indicators.
The Power LED indicates the module is receiving power.
The Fiber Optic link LEDs indicate the fiber optic connections have been established.
Verify the Link Mode selection is set to Link Segment (LS). Until a stable link is
established, leave the Link Mode configured for LS. After a Link presence is established,
the Link Mode selection can be modified.
LED Function
"Legend"
Color Off State
On / Blinking State
Power "Pwr" Amber No power On: Module has power
Port 1
Fiber Link Activity
"P1"
Green No Fiber Link
On: Fiber link is active
Blinking: Fiber Data Activity
Port 2
Fiber Link Activity
"P2"
Green No Fiber Link
On: Fiber link is active
Blinking: Fiber Data Activity
Figure D: LED Indicators
Form 040-08980-001 D 12/07
Omnitron Systems Technology * 140 Technology Dr. * #500 * Irvine, CA 92618
949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com
SW1 SW8
UP
DOWN
Bank 1
Port 1 Port 2
Figure A: DIP-Switch Location