Omega FLOWMETER FL45200A - Manual (Page 7)

Maximum Temperature vs. Pressure
Temperature
160°F / 71.1°C
150°F / 65.6°C
180°F / 82.2°C
200°F / 93.3°C
170°F / 76.7°C
190°F / 87.8°C
140°F / 60.0°C
130°F / 54.4°C
120°F / 48.9°C
110°F / 43.3°C
100°F / 37.8°C
90°F / 32.2°C
80°F / 26.7°C
70°F / 21.1°C
0 / 0 25 / 1.7 50 / 3.4 75 / 5.2 100 / 6.9 125 / 8.6 150 / 10.3
PSIg / BAR
Page 5
5
1
3
3
3
2
4
Floor
Ceiling Caution: Follow these instructions to avoid
failure.
Danger: Wear eye protection when
installing or removing flowmeter.
1. Polysulfone and other exotic plastics
cannot tolerate PVC Glue and /or pipe dope.
even fumes can cause crazing.
2. If you are installing your flowmeter to
a glued pipe configuration, install
flowmeter after all glued fittings are dried
and lines are purged of all fumes.
Use Teflon® tape (or similar) for the
flowmeters threaded adapters.
Hand tighten union nuts. No wrenches.
3. Wall, floor, and ceiling mounts are to
be carefully aligned and sturdy. Wall,
floor, and ceiling supports are recom-
mended as needed.
4. Valves - Avoid a system that will impose a sudden burst of flow to the meter. Such
a burst will cause the float to impact the float stop with destructive force. Magnet,
solenoid, or other quick opening valves cannot be used unless meter is protected
against sudden bursts of flow.
5. The maximum working pressure should not exceed 150 psi at ambient
temperature.
USA USA
IN IN
MADE MADE
WARRANTY WARRANTY
RETURN REQUESTS / INQUIRIES RETURN REQUESTS / INQUIRIES
OMEGA warrants this unit to be free of defects in materials and workmanship and to give
satisfactory service for a period of 13 months from date of purchase. OMEGA Warranty adds
an additional one (1)month grace period to the normal one (1) year product warranty to
cover handling and shipping time. This ensures that OMEGA’s customers receive maximum
coverage on each product. If the unit should malfunction, it must be returned to the factory for
evaluation. OMEGA’s Customer Service Department will issue an Authorized Return (AR)
number immediately upon phone or written request. Upon examination by OMEGA, if the unit
is found to be defective it will be repaired or replaced at no charge. However, this
WARRANTY is void if the unit shows evidence of having been tampered with or shows
evidence of being damaged as a result of excessive corrosion; or current, heat, moisture, or
vibration; improper specification; misapplication; misuse or other operating conditions outside
of OMEGA’s control. Components which wear or which are damaged by misuse are not
warranted. These include contact points, fuses, and triacs.
OMEGA is glad to offer suggestions on the use of it’s various products. Nevertheless,
OMEGA only warrants that the parts manufactured by it will be as specified and free of
defects.
OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND
WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE AND ALL IMPLIED
WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive
and the total liability of OMEGA with respect to this order, whether based on contract,
warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the
purchase price of the component upon which liability is based. In no event shall
OMEGA be liable for consequential, incidental or special damages.
Every precaution for accuracy has been taken in the preparation of this manual; however,
OMEGA ENGINEERING, INC. Neither assumes responsibility for any omissions or errors
that may appear nor assumes liability for any damages that result from the use of the
products in accordance with the information contained in this manual.
SPECIAL CONDITION: Should this equipment be used in or with any nuclear installation or
activity, purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or
damage whatsoever arising out of the use of the equipment in such a manner.
OMEGA warrants this unit to be free of defects in materials and workmanship and to give
satisfactory service for a period of
from date of purchase. OMEGA Warranty adds
an additional one (1)month grace period to the normal one to
cover handling and shipping time. This ensures that OMEGA’s customers receive maximum
coverage on each product. If the unit should malfunction, it must be returned to the factory for
evaluation. OMEGA’s Customer Service Department will issue an Authorized Return (AR)
number immediately upon phone or written request. Upon examination by OMEGA, if the unit
is found to be defective it will be repaired or replaced at no charge. However, this
WARRANTY is void if the unit shows evidence of having been tampered with or shows
evidence of being damaged as a result of excessive corrosion; or current, heat, moisture, or
vibration; improper specification; misapplication; misuse or other operating conditions outside
of OMEGA’s control. Components which wear or which are damaged by misuse are not
warranted. These include contact points, fuses, and triacs.
Every precaution for accuracy has been taken in the preparation of this manual; however,
OMEGA ENGINEERING, INC. Neither assumes responsibility for any omissions or errors
that may appear nor assumes liability for any damages that result from the use of the
products in accordance with the information contained in this manual.
: Should this equipment be used in or with any nuclear installation or
activity, purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or
damage whatsoever arising out of the use of the equipment in such a manner.
13 months
(1) year product warranty
OMEGA is glad to offer suggestions on the use of it’s various products. Nevertheless,
OMEGA only warrants that the parts manufactured by it will be as specified and free of
defects.
OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND
WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE AND ALL IMPLIED
WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive
and the total liability of OMEGA with respect to this order, whether based on contract,
warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the
purchase price of the component upon which liability is based. In no event shall
OMEGA be liable for consequential, incidental or special damages.
SPECIAL CONDITION
Direct all warranty and repair requests/inquiries to the OMEGA ENGINEERING Customer
Service Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER
MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR
number should then be marked on the outside of the return package and on any
correspondence. Direct all warranty and repair requests/inquiries to the OMEGA ENGINEERING Customer
Service Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER
MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR
number should then be marked on the outside of the return package and on any
correspondence.
FOR WARRANTY RETURNS, please have FOR NON WARRANTY REPAIRS OR FOR WARRANTY RETURNS, please have FOR NON WARRANTY REPAIRS OR
The following information available CALIBRATION, consult OMEGA for
The following information available CALIBRATION, consult OMEGA for
Before contacting OMEGA: current repair/calibration charges. Have
Before contacting OMEGA: current repair/calibration charges. Have
1. P.O. number under which the product the following information available
1. P.O. number under which the product the following information available
was was PURCHASED, PURCHASED, before before contacting contacting OMEGA: OMEGA:
2. Model and serial number of the product 1. P.O. Number to cover the COST of 2. Model and serial number of the product 1. P.O. Number to cover the COST of
under warranty, and the repair/calibration,
under warranty, and the repair/calibration,
3. Repair instructions and/or specific 2. Model and serial number of product,
3. Repair instructions and/or specific 2. Model and serial number of product,
Problems
Problems relative relative to to the the Product and Product and
3. Repair instructions and/or specific 3. Repair instructions and/or specific
Problems relative to the product. Problems relative to the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible.
This affords our customers the latest in technology and engineering.OMEGA is a registered trademark of
OMEGA ENGINEERING, INC.©Copyright 1995 OMEGA ENGINEERING, INC. All rights reserved. This
documentation may not be copied, photocopied, reproduced, translated, or reduced to any electronic
medium or machine-
readable form, in whole or in part, without written consent of OMEGA
ENGINEERING, INC.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible.
This affords our customers the latest in technology and engineering.OMEGA is a registered trademark of
OMEGA ENGINEERING, INC.©Copyright 1995 OMEGA ENGINEERING, INC. All rights reserved. This
documentation may not be copied, photocopied, reproduced, translated, or reduced to any electronic
medium or machine-
readable form, in whole or in part, without written consent of OMEGA
ENGINEERING, INC.