Tunturi T60 - Manual (Page 12)

12
OWNER’S MANUAL
•
T60
•
the alignment of the belt is correct
It is, however, possible for the belt to be pushed to one
side due to the user’s running style (e.g. more weight
on one foot). The alignment of the belt is adjusted by
turning the two bolts at the back of the treadmill.
1. Turn the power switch on and increase the treadmill’s
speed to 5 km/h (3 mph).
2. If the belt drifts to the left, turn the left adjustment
bolt ¼ turn clockwise and the right adjustment bolt 1/8
turn anti-clockwise. If the belt drifts to the right, turn
the right adjustment bolt ¼ turn clockwise and the left
adjustment bolt ¼ turn anti-clockwise.
3. If the belt remains centered the adjustment is correct.
If not, continue to make small adjustments as above
until the belt is correctly aligned. If the belt is allowed
run across to one side for long periods of time the edges
of the belt may be damaged and the treadmill may not
continue to operate correctly. Any damage to the belt
caused by the lack of necessary adjustment will not be
covered by the warranty.
ADJUSTING THE BELT TENSION
The belt must be tensioned if it begins to slip on the
rollers. In normal use, however, keep the belt as loose
as possible! The belt tension is adjusted by turning the
same screws as used for aligning the running belt. If
turning the screws will not effect the belt tension, please
contact your local Tunturi dealer.
1. Increase the treadmill’s speed to 5 km/h (3 mph).
2. Turn both adjustment screws an equal amount, ¼
turn clockwise.
3. Try to slow the belt down by holding onto the
handrails and braking as you walk (as if you were
walking downhill).
If the belt slips, turn another ¼ turn and repeat the test.
When braking heavily the belt may slip. If the belt keeps
slipping despite repeated adjustments, please contact
your local Tunturi dealer.
MALFUNCTIONS
NOTE! Despite continuous quality control, defects and
malfunctions caused by individual components may
occur in the equipment. In most cases it’s unnecessary
to take the whole device in for repair, as it’s usually
sufficient to replace the defective part. Always give
the model, serial number of your equipment and in
case of malfunctions also conditions of use, nature of
malfunction and any error code.
When you encounter unusual behavior from the
treadmill, simply turn the power switch off, wait 1
minute and turn the power switch on to reset the
treadmill. This should clear incidental errors and ready
the treadmill for normal operation again. If after you
have reset the treadmill by turning the power switch off
and on again, and the treadmill is still not operational,
contact your local Tunturi dealer for service.
If you require spare parts, always give the model, serial
number of your equipment and the spare part number
for the part you need. The spare part list is at the back
of this manual. Use only spare parts mentioned in the
spare part list.
ERROR CODES
The user interface will display information about
operational faults.
SYSTEM CHECK FAILED. Possible motor controller
fault. Turn the power switch off, wait 1 minute and
turn the power switch on again. If treadmill recovers
to normal operation, you may continue to use the
treadmill. Otherwise, call the dealer for service.
SPEED SENSOR ERROR. Call the dealer for service.
MOTOR SPEED ERROR. Ensure correct usage of
the treadmill. Do not push the belt with your feet.
Turn the power switch off, wait 1 minute and turn the
power switch on again. If treadmill recovers to normal
operation, you may continue to use the treadmill.
Otherwise, call the dealer for service.
MOTOR OVERLOAD. Ensure correct usage of the
treadmill. Do not brake the belt. Turn the power switch
off, wait 1 minute and turn the power switch on again.
If treadmill recovers to normal operation, you may
continue to use the treadmill. Ensure the lubrication
is sufficient, re-lubricate the running deck if needed.
Otherwise, call the dealer for service.
LIFT MOTOR ERROR. Call the dealer for service.
LIFT MOTOR OVERLOAD. Ensure correct usage
of the treadmill. Do not overload the lift motor by
continuously changing the elevation. Turn the power
switch off, wait 1 minute and turn the power switch on
again. The lift motor will be automatically calibrated
when the power switch is turned on. If treadmill
recovers to normal operation, you may continue to use
the treadmill. Otherwise, call the dealer for service.
MAINTENANCE CODE
CHECK LUBRICATION. Ensure the lubrication is
sufficient, re-lubricate the running deck only if needed.
Remove the code by pressing the ENTER key twice.
OVERLOAD PROTECTOR
If the treadmill’s power consumption becomes too
great, the overload protector will cut the power supply
as a safety measure. The fuse button next to the power
switch will spring up. Before you continue using the
equipment, first check the lubrication of the track, as
well as any other mechanical reason that could have
caused the overload protector to cut in. Push the fuse
button down. The treadmill is now ready for use again.
MOVING AND STORAGE
The T60 can be folded up to space saving storage
position. Always let the treadmill come to a complete
stop before lifting the running deck into the storage
T60_manual_uusi versio_j.indd 12 T60_manual_uusi versio_j.indd 12 25.10.2006 13:33:56 25.10.2006 13:33:56