Telex ELECTRO-VOICE RE-2 - Manual (Page 8)

Bodypack Trans mit ter Setup
and Op er a tion
1. In sert Bat tery. Pinch the bat tery door tabs in ward and
pull the door open. In sert a 9V bat tery as in di cated by the
+/- in the holder.
2. With bat tery com part ment still open, turn the unit on with
Power switch on the top panel. The bat tery low LED will
light for a sec ond and the dis play will show
the Group and
Chan nel num bers.
3. Change the group and chan nel num bers to match those
dis played on the re ceiver by press ing SET. The Group
num ber will flash and can be changed with the UP/DOWN
keys. Once the de sired
Group num ber is show ing, press
SET to se lect and the Chan nel num ber will flash. Se lect
the Chan nel and press SET again, the flash ing will stop
and the chan nel is now set.
4. Set Key Lock-Out. By press ing and hold ing the UP and
DOWN ar row keys to gether for 3 sec onds, the SET key is
dis abled. To re ac ti vate the SET key, sim ply press and hold
the UP and DOWN keys again for
3 sec onds.
5. Ver ify re cep tion. With the trans mit ter and re ceiver on and
match ing Group and Chan nel, the main re ceiver dis play
should be in di cat ing a RF sig nal on the bar graph. If the
level me ter does not show re cep tion, make sure the chan -
nels are match ing and re fer to the trou ble shoot ing sec tion.
6. At tach the Mi cro phone or Guitar.
Mi cro phone: Plug the mi cro phone ca ble into the top panel
of the BPU-2. Speak into the mi cro phone and the Au dio
Me ter bar graph should in di cate au dio sig nal pres ence.
Gui tar: Turn off the bodypack, press and hold SET while
you turn the bodypack on. A gui tar sym bol will ap pear in
the dis play to in di cate in stru ment mode. Re peat the pro -
cess hold ing SET on the re ceiver as it is pow ered up
to re -
turn to voice mode . Plug in the MAC-G3 gui tar ca ble.
Strum the gui tar and the Au dio Me ter bar graph on the re -
ceiver should in di cate au dio sig nal pres ence.
7. Ad just ment of the Trans mit ter Au dio Gain - (if nec es -
sary). The trans mit ter au dio gain is fac tory set at the mid -
dle of the range, which should be suit
able for most
ap pli ca tions. For loud or soft speak ers/sing ers, a gain ad -
just ment may be nec es sary.
Have the speaker or singer use the mi cro phone in a nor mal
per for mance level voice. The Au dio Me ter in the main re -
ceiver dis play screen should show peaks around the -3 dB
level. If the me ter peaks all the way to the right or well be -
low the -3 dB level, ad just the trans mit ter au dio gain.
To ad just the trans mit ter gain, gently in sert the pro vided
screw driver (or other screw driver) into the ad just ment po -
ten ti om e ter. Gently turn coun terclock wise un til the con trol
stops (the mi cro phone out put is at min i mum but not off).
Slowly turn the gain con trol up (clock wise) while speak -
ing/sing ing into the mi cro phone or strum ming the guitar
and the au diome ter shows peaks around -3 dB.
NOTE: Op er ating with the trans mit ter au dio gain set as
high as pos si ble (with out dis tor tion or peaks all the way to
the right end of the me ter) will re sult in the best per for -
mance and high est sig nal to noise ra tio.
Other Screens: Press SET and DOWN at the same time to
dis play the bat tery level. Press SET and DOWN again to
dis play fre quency. Press them one more time to re turn to
Group and Chan nel.
8. Fre quency Edit Mode - Press SET from the fre quency
dis play screen to en ter fre quency edit mode. Press the Up
and Down to ad just fre quency in 25 kHz in cre ments. Hold -
ing the Up or Down but tons down will auto step the fre -
quency; slowly at first, then quickly. You can also en ter
fre quency edit mode by press ing SET and UP at the same
time from ei ther the Group and Chan nel or Bat tery sta tus
dis play screens. Press ing SET and UP at the same time
form the Fre quency dis play screen will en ter Group and
Chan nel edit mode.
9. Power Lock Out - Press and hold SET, UP, and DOWN at
the same time and hold for 3 sec onds to lock the power
switch on. To turn the unit off, place the power switch in
the OFF po si tion and push SET, UP, or DOWN. To re -
move the lock, press SET, UP, and DOWN again at the
same time
and hold for 3 sec onds. A one-time only
ON-Lock mode can also be en tered by quickly cy cling the
power switch three times.
10. Test Per for mance - Go back to Sec tion 3 - Re ceiver Setup
& Op er a tion, Step 9 to com plete sys tem set up and test.
-6-
AP PROVAL IN FOR MA TION
The Elec tro-Voice/Telex Trans mit ters are Type Ac cepted un der United States Fed eral Com mu ni ca tions Com mis sion CFR 47,
Part 74 and In dus try Can ada RSS123.
The Elec tro-Voice/Telex Re ceiver is ap proved un der United States Fed eral Com mu ni ca tions Com mis sion CFR 47, Part 15 and
In dus try Can ada RSS210.
Li cens ing of Elec tro-Voice/Telex equip ment is the us ers re spon si bil ity and Licensability de pends upon the us ers clas si fi -
ca tion, us ers ap pli ca tion and fre quency se lected. Elec tro-Voice/Telex strongly urges the user to con tact the ap pro pri ate
tele com mu ni ca tions au thor ity for any de sired clar i fi ca tion.
CAU TION: Any changes or mod i fi ca tions made to the above equip ment could void the us ers au thor ity to op er ate the equip ment.