TOA Electronics TOA M-9000 - Manual (Page 4)

Specifications are subject to change without notice.
Printed in Japan (0612) 833-52-377-40 u
TOA Corporation
http://www.toa.jp
The T-001T is a plug-in module designed for use with the M-9000
and provide two independent balanced outputs. It can drive load
of 600
Ω up to +16dB. It can process effect for TONE/EQ/
COMPRESSOR to two inputs independently.
Power Source +24 V DC, -24 V DC, +6 V DC
Current Consumption 35 mA (at +24 V DC), 35 mA (at -24 V DC), 60 mA (at +6 V DC)
Output 2 channels, max. +20 dB* (at 10 k Ω load), 600 Ω,
electronically-balanced, removable terminal block (3 pins)
Frequency Response 20-20,000 Hz, +1, -3 dB
Total Harmonic Distortion + N 0.005% (at 1 kHz, 20 – 20,000 Hz BPF, 5 V output, 10 k Ω load)
S/N Ratio Over 73 dB (at 20 – 20,000 Hz BPF )
Residual Noise Under -91 dB (at 20 – 20,000 Hz BPF, VOL: -70 dB)
Crosstalk Over 87 dB (at 20 kHz)
D/A Converter 24 bit ∆∑DAC
Sampling Frequency 48 kHz
Tone Control Bass: ±12 dB (at 100 Hz), Treble: ±12 dB (at 10 kHz)
Parametric Equalizer 10 bands, Frequency: 20-20,000 Hz, 31 steps,
Variable range: ±12 dB, Q: 0.3-5
Speaker Equalizer 15 (compatible with TOA speakers only)
High-pass Filter -12 dB/oct, Variable frequency range: 20 – 400 Hz, 14 steps
Low-pass Filter -12 dB/oct, Variable frequency range: 4,000 – 20,000 Hz, 8 steps
Compressor Depth: 1-5
Delay 0-40 ms (1 ms step), maximum 40 ms (CH 1 + CH2), mixer mode only
Operating Temperature -10 °C to +40°C
Finish Panel: Aluminum, hair-line
Dimensions 35 (W) × 78 (H) × 91.5 (D) mm
Weight 82 g
Accessory Removable terminal plug (3 pins) × 2, Module mounting screw × 2
*0 dB = 1 V
T-001T Dual Line Output Expansion
Module with DSP
D-001T Dual Mic/Line Input
Module with DSP
The D-001T is a plug-in module designed for use with the M-9000 and
can provide two independent balanced inputs. The D-001T can handle
signals ranging from microphone level to line level by controlling their
input sensitivity in 9 increments from -60dB to -10dB.
Phantom power (+24V) can be supplied for condenser microphone use.
The D-001T can process effect for TONE/EQ/COMPRESSOR to two
inputs independently.
Power Source +24 V DC, -24 V DC, +6 V DC
Current Consumption 20 mA (at +24 V DC), 20 mA (at -24 V DC), 60 mA (at +6 V DC)
Input 2 channels, 3 k Ω (when the phantom power is ON)/
10 k Ω (when the phantom power is OFF),
electronically-balanced, removable terminal block (3 pins)
Input Sensitivity -60, -54, -48, -42, -36, -30, -24, -18, -10 dB* (selectable)
Frequency Response 20 – 20,000 Hz, +1, -3 dB
Total Harmonic Distortion + N 0.008% (at 1 kHz, 20-20,000 Hz BPF, Input sensitivity: -10 dB)
Input Equivalent Noise Under -112 dB (at 20 – 20,000 Hz BPF, Input short, Input sensitivity: -60 dB)
S/N Ratio Over 73 dB (at 20 – 20,000 Hz BPF, Input short, Input sensitivity: -10 dB)
Crosstalk Over 75 dB (at 20 kHz, Input sensitivity: -10 dB)
CMRR Over 62 dB (at 1 kHz, Input sensitivity: -60 dB)
A/D Converter 24 bit ∆∑ADC
Sampling Frequency 48 kHz
Tone Control Bass: ±12 dB (at 100 Hz), Treble: ±12 dB (at 10 kHz)
Parametric Equalizer 10 bands, Frequency: 20 – 20,000 Hz, 31 steps,
Variable range: ±12 dB, Q: 0.3-5
High-pass Filter -12 dB/oct, Variable frequency range: 20 – 400 Hz, 14 steps
Low-pass Filter -12 dB/oct, Variable frequency range: 4,000 – 20,000 Hz, 8 steps
Compressor Depth: 1 – 5
Phantom Power +24 V DC
Operating Temperature -10 °C to +40°C
Finish Panel: Aluminum, hair-line
Dimensions 35 (W) × 78 (H) × 91.5 (D) mm
Weight 82 g
Accessory Removable terminal plug (3 pins) × 2, Module mounting screw × 2
*0 dB = 1 V
The C-001T is Control I/O expansion module designed for use with the
M-9000 and can provide up to 8 channels each of input and output
expansion. Since the main unit has 4 preinstalled inputs and outputs
each, the control input and output can be expanded to up to 12
channels each when the C-001T is used.
Power Source 6 V DC
Current Consumption 15 mA
Control Input 8 channels, open voltage: 3.3 V DC, short-circuit
current: under 1 mA, removable terminal block (9 pins)
Control Output 8 channels, open collector output, withstand voltage: 27 V DC,
control current: max. 50 mA, removable terminal block (9 pins)
Operating Temperature -10 °C to +40°C
Finish Panal: Aluminum, hair-line
Dimensions 35 (W) × 78 (H) × 91.5 (D) mm
Weight 62 g
Accessory Removable terminal plug (9 pins) × 2, Module mounting screw × 2
The ZP-001T is a zone paging module designed for use with the M-9000
and functions as interface to connect the M-9000 to an analog PABX,
allowing zone paging to be initiated from the PABX. There are two
operation modes: ring signal and paging port modes.
Broadcast can be initiated regardless of operation mode.
Power Source +24 V DC, +6 V DC
Current Consumption 38 mA (at +24 V DC), 18 mA (at +6 V DC)
Number of Line 1 line
Type of Selectable Signal DTMF signal
Signaling System Loop-Start (or Ground-Start, selectable)
TEL Line 0 dB, 600 Ω, balanced, transformer-isolated, loop voltage:
24 V DC or more which should be supplied from the PABX, RJ11 connector
Paging Input 0 dB, 600 Ω, balanced, transformer-isolated audio input,
removable terminal block (4 pins)
Control Input 1 channel, no-voltage make contact, open voltage: 5 V DC,
short-circuit current: 0.5 mA, removable terminal block (4 pins)
Control Output 4 channels, open collector output (isolated), withstand voltage: 35 V DC,
control current: max. 50 mA, removable terminal block (4 pins)
Operating Temperature -10 °C to +40°C
Finish Pael: Aluminum, hair-line
Dimensions 35 (W) × 78 (H) × 91.5 (D) mm
Weight 153 g
Accessory Removable terminal plug (4 pins) × 3, Module mounting screw × 2
C-001T Input/Output Control
Module
AN-001T Ambient Noise
Control
ler Module
ZP-001T Telephone Zone
Paging Module
The AN-001T is a plug-in module of 2-channel ambient noise detector
designed for use with the M-9000.
It automatically adjusts the output volume in response to the change of
ambient noise level. The AN-001T can handle input signals from microphone
level (-60dB) to line level (-10dB) by controlling the gain in 9 steps.
Phantom power (+24V) can be supplied for condenser microphone use.
Power Source +24 V DC, -24 V DC, +6 V DC
Current Consumption 20 mA (at +24 V DC), 20 mA (at -24 V DC), 60 mA (at +6 V DC)
Input Sensor input (Ambient noise sensor microphone input):
2 channels, 3 k Ω (when the phantom power is ON)/10 kΩ
(when the phantom power is OFF), electronically-balanced,
removable terminal block (3 pins)
Input Sensitivity -60, -54, -48, -42, -36, -30, -24, -18, -10 dB* (selectable)
Phantom Power +24 V DC
A/D Converter 24 bit ∆∑ADC
Sampling Frequency 48 kHz
Ambient Noise Control Sensor input reference level adjustment function
Function Maximum output signal level control: -15 to 0 dB
Minimum output signal level control: -18 to -3 dB
Sample time setting: 10 s, 15 s, 20 s, 30 s, 1 min, 2 min, 3 min, 5 min
Gain ratio setting (Ambient noise: Output signal level):
6:3, 5:3, 4:3, 3:3, 3:4, 3:5, 3:6, 6:-3, 5:-3, 4:-3, 3:-3, 3:-4, 3:-5, 3:-6,
Operating Temperature -10 °C to +40°C
Finish Panel: Aluminum, hair-line
Dimensions 35 (W) × 78 (H) × 91.5 (D) mm
Weight 82 g
Accessory Removable terminal plug (3 pins) × 2, Module mounting screw × 2
Option Ceiling mount microphone: AN-9001
*0 dB = 1 V