Tannoy Di8DC - Manual (Page 2)

Di8DC
Tannoy United Kingdom
Tannoy North America
Tannoy Deutschland
Tannoy France T: 00 44 (0) 1236 420199
T: 00 1 (519) 745 1158
T: 00 49 (180) 1111 881
T: 00 33 (0)1 7036 7473 E: [email protected]
E: [email protected]
E: [email protected]
E: [email protected]
Tannoy adopts a policy of continuous improvement and product specification is subject to change Di8 DC data file // issue 1.06 // 15.01.08
TECHNICAL SPECIFICATIONS
System Di8DC /Di8DCt Construction
Frequency Response (-3dB) (1) 65Hz - 30kHz
Frequency Range (-10dB) (1) 53Hz - 35kHz
System Sensitivity (1W @1m) (2) 91dB (1W = 2.83V for 8 Ohms)
Dispersion (-6dB) 90 degrees conical
Driver Complement
Low Frequency 1x 200mm (8.00") Dual Concentric TM
constant directivity driver with
multi fibre paper pulp cone
High Frequency 25mm (1.00") titanium dome with
neodymium magnet system
Crossover 1.5kHz - 2nd order LF,
2nd order HF
(with dynamic HF protection)
Directivity Factor (Q) 5.5 averaged 1kHz to 10kHz
Directivity Index (DI) 7 averaged 1kHz to 10kHz
Rated Maximum SPL (2)
Average 111dB
Peak 117dB
Power Handling
Average 90W
Programme 180W
Peak 360W
Recommended Amplifier Power 180W @ 8 Ohms
Nominal Impedance 8 Ohms
Di8 DCt - Transformer Taps (bottom rotary switch)
70V 60W / 30W / 15W / 7.5W / OFF &
Low Impedance operation
100V 60W / 30W / 15W / OFF &
Low Impedance operation
Distortion
10% Full Power (8.5V) 2nd Harmonic 3rd Harmonic
250Hz 1.55% 0.42%
1kHz 0.41% 0.63%
10kHz 1.2% 0.65%
1% Full Power (2.7V) 2nd Harmonic 3rd Harmonic
250Hz 0.43% 0.48%
1kHz 0.07% 0.47%
10kHz 0.55% 0.13%
Enclosure High Impact Polystyrene (HIPS)
rated IP64 to EN60529 (IEC529)
Grille Steel, with weather resistant coating
Finish Textured Black or White paint
(custom trim colours can be supplied pre-fitted
to special order - minimum order quantity applies)
Connectors Euroblock type removable locking connector
with screw terminals with "loop through" facility
Fittings 1 x K-Ball™ Bracket Socket,
2 x M8 yoke bracket inserts
Supplied Yoke bracket
Accessories
Optional Pole mount adaptor, multi angle K-Ball™
Accessories pre-wired bracket
Dimensions 404.3 x 260 x 260.3mm (H x W x D)
(15.92 x 10.24 x 10.25”)(H x W x D)
NET Weight 7.0kg (15.87lbs)
Notes:
(1) Average over stated bandwidth. Measured at 1 metre on axis.
(2) Unweighted pink noise input, measured at 1 metre in an anechoic chamber
A full range of measurements, performance data, CLF and Ease™ Data can be
downloaded from www.tannoy.com
Full independent verification of published specifications carried out by NWAA Labs,
California can also be obtained from the downloads section of www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction
of new materials or manufacturing methods will always equal or exceed the
published specifications, which Tannoy reserves the right to alter without prior
notice. Please verify the latest specifications when dealing with critical applications.
8001 4120 Di8 DC Black 2 8.25kg (18.19lbs)
8001 4121 Di8 DC White 2 8.25kg (18.19lbs)
8001 4130 Di8 DCt Black 2 9.50kg (20.94lbs)
8001 4131 Di8 DCt White 2 9.50kg (20.94lbs)
PACKED WEIGHT PACKED QUANTITY COLOUR MODEL NAME PART NUMBER
Ordering Information