Thiel Audio Products SS1 Subwoofer - Manual (Page 7)

LEFT RIGHT CENTER L REAR R REAR
SUB
Unbal Input Right Bal Input Left Bal Input LFE Input
Right Bal Output Left Bal Output
Speaker level Inputs
Power L
R
Unbal Output L
R
L +
L – R – R +
INPUTS
OUTPUTS
Right Sub Output Remote Left Sub Output Right Bridge In Left Bridge In S / N Model SI 1 THIEL Audio Lexington, Kentucky USA www.thielaudio.com
LFE
Level Rear Wall
Distance Side Wall
Distance LFE Output LFE Input Normal Input Normal
Output Trigger On
Off
CAUTION RISK OF ELECTRIC SHOC K DO NOT OPEN AVIS: RISQUE DE CHOC ELEC TRIQUE - NE PAS OUVRIR !
THIEL SmartSub ®
Model Ser No Voltage
THIEL Audio • 1026 Nandino Boulevard • L exington, Kentucky U SA • www.thielaudio .com
On Auto
Flush Off
1.5
0.5 1.0 0
0 Off
2.0
2.0 2.5
1.0 1.5 0.5
100
60 70 80 90
50
On Replace fuse only with same rating.
Remplacer le fusible p ar un autre de la meme va leur. Fuse T6.3A L 250V for 120v T3.15A L 250V for 240 v ® C US
U.S. patent 6,801,628 other patents pendin g
120V~ 6.3A 60Hz or 230V~ 3.15A 50Hz
Right Bal Input Left Bal Input
L + L – R – R +
INPUT
OUTPUT
Power Amplifier
for main speakers
Preamp or Processor
SmartSub Integrator
Left/Right
outputs Sub
output
Main Left/Right speakers
Subwoofer
LEFT RIGHT CENTER L REAR R REAR
SUB
Unbal Input Right Bal Input Left Bal Input LFE Input Right Bal Output Left Bal Output Speaker level Inputs
Power L
R
Unbal Output L
R
L +
L – R – R +
INPUTS OUTPUTS
Right Sub Output Remote
Left Sub Output Right Bridge In Left Bridge In S / N Model SI 1 THIEL Audio Lexington, Kentucky USA www.thielaudio.com
LFE
Level Rear Wall
Distance Side Wall
Distance LFE Output LFE Input Normal Input Normal
Output Trigger On
Off
CAUTION RISK OF ELECTRIC SHOC K DO NOT OPEN AVIS: RISQUE DE CHOC ELEC TRIQUE - NE PAS OUVRIR !
THIEL SmartSub ®
Model Ser No Voltage
THIEL Audio • 1026 Nandino Boulevard • L exington, Kentucky U SA • www.thielaudio .com
On
Auto
Flush Off
1.5 0.5 1.0 0 0 Off
2.0
2.0 2.5
1.0 1.5 0.5
100
60 70 80 90
50
On Replace fuse only with same rating.
Remplacer le fusible p ar un autre de la meme valeur . Fuse T6.3A L 250V for 120 v T3.15A L 250V for 24 0v ® C US
U.S. patent 6,801,628 other patents pending
120V~ 6.3A 60Hz or 230V~ 3.15A 50Hz
Right Bal Input Left Bal Input
L + L – R – R +
INPUT
OUTPUT
Power Amplifier
for main speakers
Preamp or Processor
SmartSub Integrator
Left/Right
outputs
Sub
output
Main Left/Right speakers
Subwoofer
7
In this configuration the subwoofer is used to reproduce both the
subwoofer channel and the deep bass portion of the left and right
channels and achieves near-perfect blending of the main channel
bass with the main speakers.
Tell the processor the main speakers are large, even if they are not.
This configuration can be ideal if the main speakers play loudly
enough. It’s also perfect for audio systems where the subwoofer is
used to extend the bass range.
Connecting the SmartSub Integrator between the processor and the
main speaker power amp allows the Integrator to be used in
crossover mode so that bass can be kept from the main speakers
and reproduced by the subwoofer instead. This usually allows the
main speakers to play more loudly than otherwise so that the bass
range
and the output of the system are enhanced.
Tell the processor the main speakers are large, even if they are not.
Integrator Augment Configuration Integrator Crossover Configuration
3
The SmartSub Integrator in augment configuration
should be used if a passive crossover is not available
for your main speakers, you desire adjustability of the main
channel bass level or extension, or if you desire more than
one subwoofer in your system, or two stereo subwoofers.
4
If your main speakers do not play sufficiently loudly
due to bass overloading, then the Integrator should
be used in crossover mode to allow the transfer of low
frequency energy from the main speakers and into the
subwoofer.