TTE Technology L22HD32D - Manual (Page 17)

17
VHF/UHF/CABLE CHANNELS
Air Cable
VHF
2-13 VHF
2-13
UHF
14-69
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100) (125)
01
(5A)
NOTE:
If a channel with no broadcast is selected, the
sound will automatically be muted.
It may take a few seconds for a digital channel
picture to appear on screen after being selected.
To select the video input source
To view a signal from another device connected to
your LCD TV, such as a VCR player, press INPUT
SELECT, then press
ϳ/ϴ or corresponding Number
buttons (0-5), then press ENTER. You can select TV,
Video, Component, HDMI, PC or DVD depending on
which input jacks you used to connect your devices.
Source Selection
[0-5]:Select
0.TV
1.Video
2.Component
3.HDMI
4.PC
5.DVD
CH /
Press and release CH / . The channel automatically
stops at the next channel set into memory.
For proper operation, before selecting channels, they
should be set into the memory. See “Memorizing
channels” on pages 15 and 16.
DISPLAY
Press DISPLAY to display the current information on
the screen.
When the TV receives a digital signal, the digital
information will appear.
62-001 HDTV Moving Picture1
CH-1
Digital Air
No Program Information is available
Sleep Timer
Off
English
Full
1080i
Channel number • Station name •
Channel label (if preset) • Broadcast program name •
V-Chip rating • Signal type •
Sleep timer • Audio language •
Program guide • Picture size •
Resolution •
When the TV receives a analog signal, the analog
information will appear.
•
•
14
Analog Cable
Sleep Timer
Off
Full
480i
Channel number • Channel label (if preset) •
V-Chip rating • Signal type •
Sleep timer • Picture size •
Audio information
(Stereo or SAP) • Resolution •
Press DISPLAY again to clear the call display.
NOTE:
After a few seconds, DISPLAY screen will return to
normal TV-operation automatically.
QUICK VIEW
This button allows you to go back to the last channel
selected by pressing QUICK VIEW. Press QUICK VIEW
again to return to the last channel you were watching.
MUTE
Press MUTE to switch off the sound. The TV’s sound
will be silenced and “Mute” will appear on the screen.
The sound can be switched back on by pressing this
button again or the VOL + or –.
SLEEP
To set the TV to turn off after a preset amount of time,
press SLEEP on the remote control. The clock will
count up 10 minutes for each press of the SLEEP but-
ton (Off, 0h 10m, 0h 20m, ..., 2h 0m). After the sleep
time is programmed, the display will appear briefly
every ten minutes to remind you that the sleep timer
is operating. To confirm the sleep timer setting, press
SLEEP and the remaining time will be displayed for a
few seconds. To cancel the sleep timer, press SLEEP
repeatedly until the display turns to Off.
S l e e p T i m e r
0 h 1 0 m
Labeling channels
Channel label appear with the channel number
display each time you turn on the TV, select a
channel, or press DISPLAY.
You can choose any four characters to identify a
channel.
To create channel labels
1
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
2
Press
ϳ or ϴ to select “Channel”, then press ϶ or
ENTER.
•
51H0101A_eng.indd 17 08.3.7 5:39:16 PM