Teledex B150D - Manual (Page 13)

9) SETTING THE AREA CODE
Follow these steps to store your home area code:
1) Press PRGM . The PROGRAM MODE prompt will appear.
2) Press DIAL. SET AREA CODE and 000 will appear. The first 0 flashes.
3) Enter the desired area code.
4) When you set the area code’s last digit, press the PRGM key. The B150D
will beep once to confirm the setting. To reset the area code, simply
repeat the above steps.
NOTE: If you make a mistake while setting the area code, repeat the above steps.
10) ADJUSTING THE DISPLAY CONTRAST
Repeatedly press CONTRAST to adjust the display contrast. The B150D will beep once
when it reaches the darkest or the lightest contrast.
11) OPERATION
11.1 PLACING AND ANSWERING CALLS WITH THE HANDSET
To make a call with the handset, pick up the handset. The call timer will begin
counting the elapsed time of your call. Dial the desired number; the number will
appear in the display as you dial. To answer an incoming call, pick up the handset.
To end a call, place the handset back on the base.
11.2 PLACING AND ANSWERING CALLS WITH THE SPEAKERPHONE
To make or answer a call using the speakerphone, press SPEAKER/HEADSET. The call
timer will begin counting the elapsed time of your call. The SPEAKER indicator will
light. Dial the desired number.
To end a speakerphone call, press the SPEAKER/HEADSET key. The SPEAKER indicator
will turn off.
NOTES: The speakerphone does not operate without AC power. During a power failure, use
the handset instead. If background noise interferes with the speakerphone’s operation,
you can press the MUTE key to turn off the base’s microphone while the other party is
speaking. You cannot use the speakerphone with a headset connected to the phone.
11.3 SWITCHING BETWEEN THE HANDSET AND THE SPEAKERPHONE
To switch from handset to the speakerphone during a call, press SPEAKER/HEADSET, then
place the handset on the base.
To switch from the speakerphone to the handset, lift the handset and resume your
conversation. The speakerphone will automatically turn off.
11.4 ADJUSTING THE HANDSET VOLUME
When you pick up the handset to make or receive a call, the handset volume is preset
to the normal volume. To increase or decrease the handset volume, press VOLUME
or VOLUME .
11.5 ADJUSTING THE SPEAKERPHONE VOLUME
There are seven (7) volume levels for the speakerphone mode. To increase or
decrease the speakerphone volume, press VOLUME or VOLUME . The speakerphone
volume level is preset to level 2.
11.6 USING REDIAL
The redial function allows you to retrieve any of the last five numbers you dialed.
Press REDIAL ; the display will show the last number dialed. Press REVIEW key to
scroll to the 4th number stored, or continue to press REVIEW key to scroll to the
18) CALLER ID, CALL WAITING
18.1 CALLER ID
Caller ID is a service provided by your telephone company or service provider. When
you subscribe to this service, the telephone company sends the incoming caller’s tele-
phone number (and name, if available), and the call’s date and time, between the first
and second rings. The CID display receives and displays this information for each
call, and updates the display with the current date and time. The display also shows
if the caller information is not available, or if the sender blocks that information.
Your B150D will save up to ninety-nine (99) call records, after which it replaces the
oldest call record with each new one.
18.2 CALL WAITING
If you are using the telephone when a new call comes in, and you subscribe to call
waiting service from your telephone company, the display indicates that a new call
is being received. To answer the incoming call, press the FLASH/LINK key. To resume
the previous conversation, press the FLASH/LINK key again.
19) LED STATUS
The red LED on the top right-hand side of the B150D provides multiple indications:
LED BLINKS SLOWLY: You have a voice message waiting
LED REMAINS CONSTANTLY LIT: You have a new call in your Caller ID memory
LED FLASHES QUICKLY: You have a new incoming call
20) REVIEWING CALLER ID RECORDS
Each time you receive a call, your B150D stores a Caller ID record that you can
review later. A Caller ID record includes:
– Call number (in the order the calls are received)
– The time and date of the call
– Caller’s telephone number (if available)
– Caller’s name (if available)
To review all the Caller ID records, repeatedly press REVIEW or REVIEW .
The display will indicate END OF LIST when you reach the first or the last record in the
list.
NOTES: The display shows up to eleven (11) digits of a phone number. If an incoming phone
number is longer, the display shows only the last 11 digits.
The B150D returns to the time and date display after about twenty (20) seconds, if
you do not press a key during that time.
6 11
Teledex B150D Users Manual Teledex B150D Users Manual
SETTING AREA CODES CALLER ID, CALL WAITING
P/N 600-0480-52 Contents Copyright © 2002 Teledex LLC