Texas Instruments 46 - Manual (Page 23)

www.ti.com
Physical Description
Table 5. Bill of Materials (continued)
NOT
VALUE FOOTPRINT QTY PART NUMBER VENDOR DIGI-KEY NUMBER REF DESIGNATOR
INSTALLED
FERRITE BEADS, CONNECTORS, JUMPERS, JACKS, ICs, ETC.
Ferrite bead 1206 5 EXC-ML32A680U Panasonic P10437CT-ND FB2, FB3, FB4, FB6, FB8, FB9,
FB7 FB10
Inductor, SMT, 15-
µ
H, 2.6-A COIL-CDRH8D43 1 CDRH8D43-150 Sumida L1
Inductor, SMT, 5- µ H, 2.9-A COIL-CDRH6D38 1 CDRH6D38-5R0 Sumida CDRH6D38-5R0NC-ND L2
0.0-
Ω
, 1/8-W, 5% resistor 805 2 ERJ-6GEY0R00V Panasonic P0.0ACT-ND L3, L4
Red test point Test_point2 8 5000k Keystone 5000K-ND TP1, TP4, TP9, TP10 TP3 TP11
TP12 TP13
Black test point Test_point2 4 5001k Keystone 5000K-ND TP5 TP6 TP7 TP8
40-pin header 20
Ч
2
Ч
.1 1 HTSW-120-07-L-D Samtec J4
40-pin header smt 20X2_SMT_MMS_ 2 MMS-120-02-T-DV Samtec J5, J6
SAMTEC
Red banana jacks BANANA_JACK 5 ST-351A Allied N/A J11, J12, J13, J14,
J15
Black banana jacks BANANA_JACK 4 ST-351B Allied N/A J9, J10, J16, J17
SMA connectors SMA_Jack 3 901-144-8RFX AMP ARFX1231-ND J1, J3, J7 J8
3POS_header 3pos_jumper 1 HTSW-150-07-L-S Samtec JP2 (1)
6-pin header 6 Ч 1 Ч .1 1 HTSW-120-07-L-D Samtec JP1
3-pin power connector 3term_screw_con 0 93F7124 Newark J20
Transformer TC4-1W_ 3 TC4-1W Mini-Circuits T1, T2, T3
TRANSFORMER
Diode, Schottky, 1-A, 20-V DIODE-MBRM120 1 MBRM120E ON Semiconductor D2
Diode, Schottky, 3-A, 20-V DO-214AB(SMC) 1 SS32 Vishay D1
Green SM_LED_1206 LED-1206 2 CMD15-21VGC/TR8 Panasonic L62205CT-ND D3, D4
MOSFET, P-CH, 20-V, 4.7-A, 3-SOT-23 2 SI2323DS Vishay Q1, Q2
39-M
Ω
TRANS BIAS NPN, 50-V SOT416 1 DTC114EET1 ON Semiconductor DTC114EET1OS-ND Q3
Switch EVQ-PJ 1 EVQ-PJX04M Panasonic P8050SCT-ND S1
Switch, 8-Pos, half-pitch SMT SWITCH_8POS_ 1 TDA08H0SK1 ITT CKN1365-ND SW1
SMT
3-circuit jumpers SJP3_RESISTOR 2 ERJ-3GEY0R00V Panasonic P0.0GCT-ND SJP4 (2) , SJP5 (3)
3-circuit jumpers SJP3_402 2 ERJ-2GE0R00X Panasonic P0.0JCT-ND SJP1 (4) , SJP2 (5)
(1) Add jumper for JP2 between pins 1 to 2.
(2) Add jumper for SJP4 between pins 2 and 3 (use a 0- Ω resistor to short pins).
(3) Add jumper for SJP5 between pins 2 and 3 (use a 0- Ω resistor to short pins).
(4) Add jumper for SJP1 between pins 1 and 2 (use a 0- Ω resistor to short pins).
(5) Add jumper for SJP2 between pins 1 and 2 (use a 0- Ω resistor to short pins).
SLWU028B – January 2006 – Revised November 2006 23
Submit Documentation Feedback