Tech4o Northstar CW2 - Manual (Page 2)

hold
hold
Increase
Decrease
Increase
faster
Decrease
faster
[ST/STP]
[ST/STP]
[LAP/RESET]
[LAP/RESET]
[MODE]
[MODE]
[MODE]
[MODE]
minute
hour
hold
second
Countdown Timer Mode
beats per
minute
Pace Display
hold
hold
Increase
Decrease
Increase
faster
Decrease
faster
[ST/STP]
[ST/STP]
[LAP/RESET]
[LAP/RESET]
[MODE] [MODE]
40 180
x 5 BPM
40 180
x 5 BPM
hold
dual time
(hour)
animated
bar graph
dual time
(second)
dual time
(minute)
Dual Time Mode
run time
(hour)
run time
(second) 1/100 sec
run time
(minute)
lap time
elapsed time
(stopped)
elapsed
time (run)
[LAP/
RESET]
[LAP/RESET]
[ST/STP]
[ST/STP]
Lap Display
Run Display Zero Display
Stopped Display
COUNTDOWN TIMER MODE
This watch is a countdown timer
• Measurement unit: 1 second
• Measuring capacity: 99 hours 59 minutes & 59 seconds
• The watch will descend from the target time to zero
Countdown Timer Display
• The running time (hour, minute) -
displays in the 2nd row
• The running time (seconds) -
displays in the 3rd row
• Animated (1 second) - displays in
the perimeter bar graph
To Set the Countdown Timer Target Time
• In the Countdown Timer Mode,
Press and Hold [ MODE ] for 2
seconds until the "seconds"
digits flash
• Press [ MODE ] to navigate to the
setting that you wish to change.
See navigation chart at right
• When the setting you wish to
change flashes, Press [ ST/STP ]
to raise the value or [ LAP/RESET ]
to lower the value. Note: If you
Press and Hold the button, the
rate of change is faster
• When the hour is set, Press
[ MODE ] to confirm
animated
bar graph
running time
(minute)
running time
(hour)
running time
(second)
Countdown Timer
PACE MODE
Pace mode allows users to track their paces
while performing advanced orienteering
techniques in the wilderness. Users will match
their hiking pace with the pacer function’s
audible beeps to maintain and track their speed
and distances over unfamiliar terrain.
• The rate can be set in a range from 40 beats
per minute to 180 beats per minute in 5 beat
increments
Pace Display
• The rate (beats per minute) -
displays in the 2nd row
To Use the Pace Feature
• Once a pace rate has
been set (expl. 60 BPM),
Press [ ST/STP ] to start
the sound. Press [ ST/STP ]
again to stop
To set the Pace
• In the Pace Mode, Press
and Hold [ MODE ] for 2
seconds until the "beat
rate" digits flash
• Press [ ST/STP ] to raise
the value or [ LAP/RESET ]
to lower the value. Note: If
you Press and Hold the button, the rate of
change is faster
• When the rate is set, Press [ MODE ] to confirm
NOTE: If NO INPUT for 1 minute during setup, display
will default to Pace Mode
DUAL TIME MODE
This watch is a dual time piece.
Dual time is synchronized with
current time
Dual Time Display
• Dual time (hour, minute) -
displays in the 2nd row
• Dual time (seconds) -
displays in the 3rd row
• Animated (1 second) -
displays in the perimeter
bar graph
CHRONOGRAPH MODE:
This watch is a stopwatch
• Measurement unit: 1/100th second
• Measuring capacity: 99 hours 59 minutes & 59.99 seconds
• The watch will measure elapsed time, lap time and display elapsed time without
stopping measurement
Chronograph Display
• Running time (hour, minute) - displays
in the 2nd row
• Running time (second, 1/100th second)
- displays in the 3rd row
• Animated (1/100th of a second) -
displays in the perimeter bar graph
To Measure Elapsed Time
• In Zero Display, Press [ ST/STP ] once to
start measurement - ( the digits will
advance). Press [ ST/STP ] once again to stop
- (digits will not advance) The elapsed time
between the 1st Press [ ST/STP ] and the
2nd Press [ ST/STP ] will display
To Display Lap Time
• With the chronograph active, Press [
LAP/RESET ] and the cumulative lap
times will display
• Press [ LAP/RESET ] again to return to
counting display.
NOTE: When the lap time is displayed the
elapsed time is still being measured in the
background
To Reset the Chronograph
• If you wish to record a new set of elapsed
times, Press (when the chronograph has
stopped) [ LAP/RESET ] to reset the
chronograph
NOTE: If NO INPUT for 1 minute during the setup, the display will default to the
Countdown Timer Mode
To Use the Timer
• Once a target time has been set (expl. 15 min. ) Press [ ST/STP ] to start
(digits will descend to zero). Press [ ST/STP ] again to terminate the countdown
(digits will stop)
• Elapsed time will display through out the countdown
To Reload the Timer
• Press (when the timer has stopped) [ LAP/RESET ] to reload the target time
Alarm Sound
• The watch will beep once when it reaches 5, 4, 3, 2 and 1 seconds
• The watch will sound a long beep at zero.
NOTE: Press [ MODE ] to exit the Countdown Timer