Toshiba 48-1250 A - Manual (Page 24)

TD - Series
- 18 -
TD Series Digital Solid State Soft Starter 48 - 1250A
5.4.4 Kick Start Mode Functions
5.4.5 Decel Mode Functions
5.4.6 Protection Features
Fn Group Function
Adjustment
Range
Setting
Increments
Factory
Setting
Section
F025 Deceleration Ramp
0=Disabled / Coast to Stop
1=Enabled (except in event of OL Trip)
2=Enabled (continued Decel on OL Trip)
1 0 (Disabled) 5.5.5
F026 Begin Decel Level (BDL) 0 - 100 % 1% 60% 5.5.5
F027 Decel Shut Off Voltage 0 to (BDL minus 1)% 1% 30% 5.5.5
F028 Decel Ramp Time 1 - 60 Seconds 1 second 10 seconds 5.5.5
F029 Reserved Reserved Reserved Reserved 5.5.5
De
ce
l
M
ode
Fn Group Function
Adjustment
Range
Setting
Increments
Factory
Setting
Section
F030 Current Imbalance Trip
0=Disabled
1=Enabled
1 0 (Disabled) 5.5.6
F031 Current Imbalance Trip % 5 - 30% 1% 10% 5.5.6
F032 Current Imbalance Trip Delay 1 - 20 seconds 1 second 2 seconds 5.5.6
F033 Over Current / Shear Pin Trip
0=Disabled
1=Enabled
1 0 (Disabled) 5.5.6
F034 Over Current / Shear Pin Trip % 50 - 300% (note1) 1% 125% 5.5.6
F035 Over Current Trip Delay 1 - 20 seconds 1 second 1 second 5.5.6
F036 Under Current Trip
0=Disabled
1=Enabled
1 0 (Disabled) 5.5.6
F037 Under Current Trip % 10 - 90% (note1) 1% 40% 5.5.6
F038 Under Current Trip Delay 1 - 60 seconds 1 second 2 seconds 5.5.6
F039 Coast Down Lockout Timer
0=Disabled
1=Enabled
1 0 (Disabled) 5.5.6
F040 Coast Down Lockout Time 1 - 60 minutes 1 minute 5 minutes 5.5.6
F041 Starts per Hour Lockout
0=Disabled
1=Enabled
1 0 (Disabled) 5.5.6
F042 Maximum Starts per Hour 1 - 10 1 2 5.5.6
F043 Time Between Starts Lockout
0=Disabled
1=Enabled
1 0 (Disabled) 5.5.6
F044 Minimum Time Between Starts 1 - 60 minutes 1 minute 15 minutes 5.5.6
F045 Coast Down Timer Value 1 - 3600 Seconds View Only 0 5.5.6
F046 Starts per Hour Timer Value 1 - 3600 Seconds View Only 0 5.5.6
F047 Starts per Hour Count Value 1 - 10 Starts View Only 0 5.5.6
F048 Time Value Between Starts 1 - 3600 Seconds View Only 0 5.5.6
F049 Thermal Capacity to Start 0 - 100 % Thermal Capacity View Only 0 5.5.6
P
rot
ec
tion Featu
res
Fn Group Function
Adjustment
Range
Setting
Increments
Factory
Setting
Section
F022 Kick Start
0=Disabled
1=Enabled
1 0 (Disabled) 5.5.4
F023 Kick Voltage 10 - 100% 1% 65% 5.5.4
F024 Kick Time 0.1 - 2 Seconds 0.1 second 0.8 seconds 5.5.4
Kic
k Sta
rt
Mode