Team Products PMD8129 Model - Manual (Page 4)

PMD8129 Models Owner’s Manual
7. Maintain tools with care. Keep cutting tools sharp and clean.
Properly maintained tools with sharp cutting edge are less likely to bind and
are easier to control.
8. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool’s operation.
If damaged, have the tool serviced before using. Many accidents are
caused by poorly maintained tools.
9. Use only accessories that are recommended by the manufacturer
for your model. Accessories that may be suitable for one tool may create
a risk of injury when used on another tool.
Service
1.
Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel may result in a
risk of injury.
2. When servicing a tool, use only identical replacement parts.
Follow instructions in the Maintenance section of this manual. Use
of unauthorized parts or failure to follow Maintenance Instructions may
create a risk of shock or injury.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
1.
Hold tool by insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring.
Contact with a “live” wire will also make exposed metal parts of the tool
“live” and shock the operator.
2. Keep hands clear of moving parts.
3. Do not touch moving parts. Allow the power tool accessories (bit and
blades etc.) to cool before touching them. They can become extremely hot
during use and can burn your skin.
4. WARNING: This product contains chemicals, including lead, known to the
State of California to cause cancer, and birth defects or other reproductive
harm.
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER:
1. This manual includes important safety instructions for the battery charger.
Fully read all instructions and warning labels before using the battery or
battery charger.
2. To reduce the risk of electric shock or injury, use ONLY the battery charger
supplied with this unit to charge the battery. If you separately purchase a
COLEMAN® Pro Series™ Fast Charger, it may be used to charge a
separately purchased COLEMAN® Pro Series™ Fast Charge replacement
battery. The Fast Charger cannot be used to charge the battery(ies) included
with this drill.
3 4
3. Do NOT expose the battery or battery charger to rain or moisture.
4. Use of any attachment not recommended in this manual may result in the
risk of fire, electric shock or injury to person and will void the warranty.
5. To reduce the risk of damaging the battery charger power cord, be sure to
pull the plug rather then the cord when disconnecting it from the power
supply. Always position the cord so it will not be stepped on or tripped over.
This will prevent damage to the cord.
6. An extension cord should not be used unless absolutely necessary. Use of
an improper extension cord can result in risk of fire or electric shock. If
using an extension cord make sure that:
A) The pins on the plug of the extension cord are the same
number, size and shape as those on the plug on the charger.
B) The extension cord is properly wired and in good working
condition.
C) The wire size is the same or larger than the ones specified
below:
Recommended size of Extension Cord for Battery Charger
Length of Cord (Feet) 25 50 100 150
AWG Size of Cord* 18 18 16 14
* The smaller the AWG (American Wire Gauge) number of the extension cord,
the higher the capacity of the cable for conducting current to ensure proper
usage of the tool.
7. Do not operate charger with a damaged cord or plug.
8. Do not operate the charger if it has received a sharp blow, been dropped or
damaged in any other way.
9. Do not open the drill, battery or battery charger. There are no user
serviceable parts. Opening the unit will void the warranty.
10. Unplug the charger from its power source when not in use.
11. Do not touch the terminals inside the battery charger with any other metal
object such as nails or coins. This can short the charger.
12. Do not store the unit in areas where the temperature can exceed 120F(48°C).
13. Do not throw the battery or battery charger in fire. This can cause an
explosion.