Univex Aquastop 800 series - Manual (Page 9)

9
Accessories
Pedestal Mounting Kit
A storage pedestal with a pull-out
drawer is available as an accessory for
your washer. The pedestal adds 15
inches to the height of the washer.
d CAUTION
Appliance must not be mounted
on a pedestal in stacked
installations.
part no. WTZ 1610 is for a solid white
color pedestal.
Other color pedestals may be
available.
Reference part no. WTZ 1610" X" in
which the X designates an available
color (eg: A for Anthracite, S for silver).
Please inquire at your dealer for color
choices available.
You may also consult a current product
catalog or visit our website at:
www.boschappliances.com
If mounting the washer on the pedestal,
follow the instructions supplied with the
pedestal.
i If mounting the washer on a
pedestal, install the washer on the
pedestal prior to removing the
transport bolt assemblies from the
rear of the washer (see page 11 for
details).
Stacking Kits
There are two stacking kits available.
Basic Stacking Kit
This kit anchors the dryer on top of the
washer and adds approximately 0.63
inches (16 mm) to the stacked height.
part no. WTZ 1601 is for the basic
mechanical stacking kit.
Pull-Out Shelf Stacking Kit
This kit serves to stack the dryer on top
of the washer and also provides a pull-
out shelf. This kit adds approximately
1.5 inches (38.5 mm) to the stacked
washer/dryer height.
This kit may also be combined with the
pedestal accessory. The stacking kit
will add approximately 1.52 inches and
the pedestal will add approximately 15
inches to the height of the installed
washer.
i The pedestal cannot be used for
washer/dryer stacked installations.
part no. WTZ 1600 is for the solid
white pull-out shelf stacking kit.
Other color pull-out shelf stacking
kits may be available.
Reference part no. WTZ 1600" X" in
which the X designates an available
color (eg: A for Anthracite, S for silver).
Please inquire at your dealer for color
choices available.
Minimum Distances
Important information concerning
minimum distances:
- If the washer is to be installed with
a dryer so that the fronts of the
appliances are to be flush with one
another it is necessary to allow
additional rear clearance for the
dryer venting system. Depending
on the location of the exhaust air
connection, a minimum distance
of 5 ¼ inch (13.4 cm) must be
provided for ducts/brackets (see
dryer installation instructions).
- Benefits of maintaining greater
distance (clearances) than the
minimum shown include:
S reduction of the risk of mold
formation behind the appliances.
S reduced noise transmission
S facilitation of installation and
service.
S more air cools the dryer, keeps
the dryer from overheating, and
improves drying performance.
- If the washer and dryer are to be
installed in a small room, the doors
of the room must be fitted with
vents of a specified minimum size.
Refer to the following illustrations
of enclosed installations for
additional information.
- Allow additional clearance for
door, wall and window molding
where necessary.
Installation Types
Observe the following minimum
clearances between the washer and
adjacent surfaces for all installation
types.
Minimum Installation Clearances
A
Sides 0.25 in. (6.4 mm)
B Top 0.25 in. (6.4 mm)
C Rear* 2.55 in. (64.8 mm)
D Front 0.50 in. (12.8 mm)
* as close to wall as venting or water
connection will allow. If installed with a
dryer, the larger rear clearance for dryer
venting is required for the laundry pair.
q Units are designed so the dryer
can be stacked on top of the
washer using one of the stacking
kits shown on page 9.
q Units are designed to allow for
under-counter installation, see
required dimensions in under-
counter installation section on
page 10.
Height measurements shown in this
section are with the washer feet at
minimum extension (turned in all the
way up against the base of the washer).
Recessed or Closet
Dimensions for installation in a closet or
recessed area are shown in the
illustration below.
Closet Ventilation Requirements
E
Top 48 sq. in. (310 sq. cm)
F Bottom 24 sq. in. (155 sq. cm)
Required Installation Space
G
Height 37.25 in. (94.6 cm)
H Width 27.50 in. (69.9 cm)
I Depth 33.50 in. (85.1 cm)