Vizio VW22L - Manual (Page 2)

©2008 VIZIO Inc.
Programming your TV to Receive and Display Channels:
All you need is your Remote Control.
Your new TV set is now ready
to automatically reproduce the best picture quality from the input
signal being fed into it. Enjoy your VIZIO HDTV.
Programming Your Cable or
Satellite Box Remote
Consult your Cable or Satellite Owner’s Manual to determine if you
need a 3, 4 or 5-digit code. If your Cable or Satellite Box requires:
• 3-digits, please use “627” (This code usually works with DISHNetwork.)
• 4-digits, please use “1758”, “0178” or “0128”
• 5-digits, please use “11758”, “10178” or “10128” (These codes usually work
with DIRECTV.)
These small arrows correspond to
the arrows shown in the above Steps.
They surround the OK key.
OK
Legend
Optional Components
ENHANCE YOUR VIZIO EXPERIENCE
When it comes to components and accessories, don’t settle for
less than VIZIO. We offer a full line of products specifically
designed to accentuate your VIZIO HDTV. To learn more about
how you can enhance your VIZIO experience, call 888-849-4623
or visit www.VIZIO.com.
VIZIO HIGH-DEFINITION CERTIFIED CABLES
Our VIZIO Certified HD cables carry the same standards of
excellence as all our VIZIO products. Available in: DVI, HDMI
and Component in lengths of 2, 5, and 10 meters.
VIZIO CERTIFIED MOUNTS
FLUSH MOUNT- turn your HDTV into a work of art
TILT MOUNT- adjust your HDTV for the most comfortable
viewing position
ARTICULATING ARM- position your HDTV exactly where
you want it
 Coaxial connection (RF connector) is recognized as the threaded connector, commonly
called cable, screw on or coaxial connector which carries the image (picture) and sound
(audio) through a single cable.
 Composite connection (RCA connectors) is recognized by the three (yellow, red and
white) standardized color coded RCA connectors. Yellow carries the image (picture); red
(right channel) and white (left channel) carry the sound (audio) of the signal.
 Component connection (RCA connectors) is recognized by the three (green, blue and
red) standardized color coded RCA connectors for image (picture) plus the two (red and
white) standardized color coded RCA connectors for the sound (audio) of the signal.
 HDMI (High-Definition Multimedia Interface) connection (HDMI connector) is
recognized by the standardized elongated D-Shaped connector which carries both the
image (picture) and the sound (audio) of the signal through a single cable.
 S-Video (separate video) connection (4-pin Mini-DIN connector) is recognized by the
small connectors at the end of a cable with multiple pins in it. This connection carries only
the image (picture) of the signal; therefore, there is a need to supply a separate sound
(audio) signal by using the two (red and white) standardized color coded RCA connectors.
* For Your Information:
 Attaching the Base
STEP 1.1
Important: The Base of the HDTV must be assembled prior to usage.
 Place the VW22L face down on a soft
and flat surface (blanket, foam, cloth,
etc.) to prevent any damage to
the HDTV.
 Carefully align and insert the Base to
the stand (please refer to the
illustration to the right).
 Gently push the Base towards the HDTV
until the locking mechanism locks into place.
 Insert the provided M4-16mm
screw to the bottom of the
base (as shown on the
illustration to the left).
 Use a Phillips screwdriver to
tighten the Base to the stand.
 Receiving Channels through DTV/TV Input using Regular
Antenna or Regular Cable Service (No Box) Signals.
STEP 2.1
 Connect your signal source (cable
from antenna or cable from the wall for
Cable Service without box) directly to
the DTV/TV RF (commonly named
COAXIAL) connector.
STEP 2.2
 Turn on the TV; press the MENU key to obtain the above display. By default the TV will
show over the air (OTA) signal, press button to highlight Tuning Band. Press again if
the signal is cable service.
Press the button to select Auto Search, for either OTA or Cable Service the following
display will show up.
 Please wait for the TV to complete
this process or press the EXIT key
to cancel the scanning process.
 After completing the scanning,the
display will show the first found
channel.
VW22L HDTV QUICKSTART GUIDE
10T
 Displaying Channels from different Signal Sources (External TV Tuner, VCR, Cable Box
or Satellite Receiver) through different Inputs.
STEP 3.1
 Select the correct input connection; RF (DTV/TV)*
connector, Composite (Yellow, Red and White)*
connectors, Component (Red, Green, Blue plus Red
and White)* connectors, HDMI* connectors or
S-Video (AV)* plus Red and White connectors (if
applicable). Make the physical connection or hook up.
STEP 3.2
 Turn on the TV set
 Select the input by pressing the button corresponding to that specific type of connection on the remote control.
 If you have an HD service you must use the HDMI (best) or Component connection.
NOTE: Composite and S-VIDEO Cables can only be used for SD (480i) pictures.
 Turn on your Cable Box, VCR, External TV Tuner or Satellite Receiver and you will see a picture on your TV set. If there is not a
picture, make sure you have selected the correct input on the TV set.
 If the selected input is RF connection, you should be aware that the TV set needs to be on either channel 3 or channel 4 matching the
channel which has been selected on the back of the VCR, Cable Box, External TV Tuner or Satellite Receiver; please refer to the Owner or
User’s Manual of such equipment for details.
NOTE: The TV set will be displaying any television station or program selected by the Cable Box, VCR, External Tuner or Satellite Receiver. The TV
set will not be able to change programs or channels; this is controlled by the equipment sending the signal. If the service being used is the one which
setup includes a box with two different outputs for two different (distant) rooms, then scanning channels would help you to find the signal. Be aware
that the channel to be selected varies from provider to provider; meaning that, you may have to call your provider company so they could provide you
the specific channel when using high definition made TV sets. Some examples of these channels are: 105, 106, 115 and 116.