VTech DS3111-2 - Manual

Quick start guide
for model DS3111-2
NOTES:
1. Use only the power adapters and batteries supplied with your VTech
telephone.
2. For complete feature instructions, please refer to your user’s manual.
96-006499-030-100
issue 2
IMPORTANT!
If your product is not working properly:
Refer to the Troubleshooting section of the user’s manual.
Visit our website at www.vtechphones.com.
In Canada, go to www.vtechcanada.com.
Call our customer service at 1 (800) 595-9511.
In Canada, call 1 (800) 267-7377.
•
•
•
Telephone base installation
We recommend that you install the telephone base away from any electronic
equipment and appliances such as personal computers, computer routers,
television sets, microwave ovens or refrigerators. Avoid excessive heat,
cold, dust or moisture. When a location is selected, install the telephone
base and the charger as shown below. Make sure that the electrical outlet
is not controlled by a wall switch.
MANUFACTURED IN CHINA COMPLIES WITH 47 CFR PART 68 REGISTRATION NO.: US:EW7W401B80-565600 RINGER EQUIVALENCE: 0.1B USOC JACK: RJ11C/RJ11W HAC FCC ID: EW780-5656-00 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE. DC 6V 300mA CLASS 2 POWER SOURCE ONLY
TELEPHONE EQUIPMENT
Telephone
wall jack
Electrical outlet
not controlled
by a wall switch
Power adapter
Charger adapter
Telephone
line cord
Handset battery installation
Install the handset battery by following these steps:
1. Align the two holes of the battery plug with the socket pins in the handset
battery compartment, matching the red and black wires to the color-
coded label.
2. Place the battery in the compartment with the wires in the lower right
corner.
3. Position the battery compartment cover and slide it towards the unit
until it clicks into place.
For optimal performance, we recommend that you charge the handset for
16 hours. You can keep the battery charged by returning the handset to the
telephone base after each use. When the battery power is fully depleted,
a full recharge takes about 16 hours.
IC :x xx xX -x xx xx xx x
FCC ID: XXxxx-xxxx-xx IC:xxxxX-xxxxxxxx FCC ID: XXxxx-xxxx-xx IC:xxxxX-xxxxxxxx FCC ID: XXxxx-xxxx-xx
IC :x xx xX -x xx xx xx x
FCC ID: XXxxx-xxxx-xx
Make, receive and end calls
Make a call
• Press / FLASH or to ensure there is a dial tone, then dial the
telephone number.
-OR-
1. Dial the number (press MUTE/REMOVE to make corrections;
press and hold REDIAL/PAUSE to insert a dialing pause).
2. Press /FLASH or to use the speakerphone.
Receive a call
• Press / FLASH, or any dialing keys (0-9, * or # ) to answer an
incoming call.
End a call
• Press OFF/CLEAR or put the handset back in the telephone base
or charger.
Voicemail setup
This feature allows you to use the VOICEMAIL, PLAY, SKIP and ERASE
buttons to access your voicemail (a subscription service available from
your local telephone company for a fee). Before completing these steps, be
sure to have your access number and password to access your voicemail
available. You will also need the key sequence to play, skip and delete your
messages. Contact your local telephone company for more information
about voicemail service.
To program the
ACCESS NUMBER button:
1. Press MENU/SELECT from the idle mode.
2. Press or to select VOICEMAIL SETUP, then press
MENU/SELECT.
3. Press or to select ACCESS NUMBER, then press
MENU/SELECT.
4. Use the dial pad to enter the access number. Press MUTE/REMOVE
to delete characters if necessary.
5. Press MENU/SELECT. You’ll hear a confirmation tone.
To program the PASSWORD, PLAY, SKIP and ERASE buttons, follow
the above steps.
To program a pause:
1. Press
MENU/SELECT from the idle mode.
2. Press or to select VOICEMAIL SETUP then press MENU/SELECT
twice.
3. The blinking cursor should be at the end of your access number. Press
and hold the REDIAL/PAUSE button until a P appears.
4. Press MENU/SELECT. You’ll hear a confirmation tone.
To reset all codes:
1. Press
MENU/SELECT from the idle mode.
2. Press or to select VOICEMAIL SETUP then press MENU/SELECT.
3. Press or to select RESET ALL CODES, then press
MENU/SELECT.
4. The screen displays RESET CODES?
5. Press MENU/SELECT. You’ll hear a confirmation tone.
NOTE:
You must program your voicemail buttons before you can access all of
the functions available with your voicemail.
QSG DS3111-2 071207.indd 1 7/28/2007 5:54:04 PM