Verbatim Store 'n' Go Hi-Speed USB - Manual (Page 9)

SYSTEM
REQUIREMENTS
Hardware:
Store ‘n’ Go Professional plugs into any PC
or Apple Macintosh with a USB port.
Software:
No special software is required for systems running on
Windows 2000, Windows Millennium Edition, Windows XP,
Linux 2.6.0, and Macintosh OS 9.x, 10.x. For systems running
Windows 98 driver files must be installed before using
Store ‘n’ Go Professional for the first time.
A Windows 98 driver is available at our web site
www.verbatim-europe.com.
Note that earlier versions of windows including Windows 95
do not support USB Mass Storage Class Devices and
consequently are not compatible with Store ‘n’ Go Professional.
PRECAUTIONS
• When the indicator light is blinking rapidly, Store ‘n’ Go
Professional is transferring data between itself and
the host computer. Do not remove Store ‘n’ Go
Professional until the light slows to a slow, regular pulse.
• Deactivate Store ‘n’ Go Professional before removing it
from the USB port.
• Keep your Store ‘n’ Go Professional away from water,
extreme moisture or heat.
• Keep your Store ‘n’ Go Professional away from
electrostatic sources and magnetic fields.
• Store your Store ‘n’ Go Professional with its cap in place.
• Do not force Store ‘n’ Go Professional into the USB port.
If the port resists smooth insertion of Store ‘n’ Go
Professional, check that the device is positioned
with the USB icon on top and that the port is
free of obstructions.
Store’n’Go Professional
Host Interface Universal Serial Bus
(USB 2.0 High Speed and Full Speed)
Power Supply USB bus powered
No external power required
(high power device)
Power consumption Standby: 790uA (typical), 1.0mA (max)
Read/write:
High Speed: 105mA (typical), 125mA (max)
Full Speed:
75mA (typical), 105mA (max)
Transfer Rate High Speed: Read upto 23MB/sec,
write upto 14MB/sec
Full Speed: Read upto 1MB/sec,
write upto 1MB/sec
Supported Operating Windows 98SE, 2000, Me, XP
Systems Macintosh 9.x, 10.x
Linux kernel version 2.6.x (tested with
RedHat, Suse and Turbo Linux)
LED Indicators LED flashing slowly –
connected and inactive
LED flashing rapidly –
transmitting/receiving data
LED Colours –
Blue USB High Speed Mode
– Red USB Full Speed Mode
Operating Temperature 0° C to 60° C
Storage Temperature -40°C to 70°C
Environment Relative humidity 5% to 90%
Altitude Operating 6,096m (20,000ft)
Storage 12,192m (40,000ft)
Vibration 5G RMS, 10 to 2,000Hz,
0.5 Oct/min sweep rate
Shock Non operating 55G, 11ms, half-sine
Certification FCC, CD, VCCI, CE, TUV, WHQL
3
VERBATIM LIMITED LIFETIME WARRANTY
Verbatim Corporation warrants this product to be free from defects in material and workmanship If this product is found to be
defective, it will be replaced at no cost to you. You may return it with your original cash register receipt to the place of purchase
or contact Verbatim.
In the following European countries, Austria, Belgium, Denmark, Finland, France, Germany, Greece, Hungary, Italy, Luxembourg,
Monaco, Netherlands, Norway, Poland, Portugal, Republic of Ireland, Spain, Sweden, Switzerland, call 00 800 3883 2222.
All other European countries call +353 61 226586.
You can email [email protected].
In the U.S. and Canada, call 800-538-8589 or email [email protected].
Product replacement is your sole remedy under this warranty, and this warranty does not apply to normal wear or to damage
resulting from abnormal use, misuse, abuse, neglect or accident, or to any incompatibility or poor performance due to the specific
computer software or hardware used. VERBATIM WILL NOT BE LIABLE FOR DATA LOSS OR ANY INCIDENTAL, CONSEQUENTIAL
OR SPECIAL DAMAGES, HOWEVER CAUSED, FOR BREACH OF WARRANTIES OR OTHERWISE. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state or country to country.
NOTE: Verbatim Corporation may at any time revise the content of this user guide without further notice.